Laptops and Tablets • Recommendations and advice


Install SSD Into Laptop Instead of Dvd

Removing the top cover

Now we need to remove the top cover of the laptop by unscrewing all the fixing screws. You should take into account the fact that they come in different sizes and you definitely need to remember where they were unscrewed from.

After all the screws are unscrewed, it is up to the pick. Now you need to separate the bottom and top of the laptop. You need to be extremely careful when opening it, since most models have NOT reliable latches, which can easily break. Check again if all the screws have been loosened, otherwise there is a risk of damage to the device case.

install, laptop, instead

To remove the cover, you need to insert the pick into the gap between the top and bottom covers, and slowly twist it to release the latches inside the case. Start at the front of the laptop where the indicator lights are located. It is necessary to walk the pick along the perimeter of the entire body.

When working with some devices, you do not have to disconnect the cables, since sometimes you can replace the DVD drive without removing the upper part of the device, which can significantly save your time.

How to choose an adapter?

The size of the drive can be of two types and differ in its thickness. 9.5mm and 12.7mm. Before purchasing an adapter, carefully measure the thickness of your drive and only then buy the Corresponding adapter. Otherwise, the SSD drive adapter simply won’t fit into the laptop instead of the DVD drive.

You should also pay attention to the interface through which the drive is connected. If the interface is SATA, then Using an adapter with an adapter to mSATA, you can easily put an SSD instead of a floppy drive. But if your DVD drive is connected via IDE, and this is an outdated technology, then you need an IDE to SATA adapter to connect an SSD.

As mentioned above, adapters differ only in thickness, while their shape and width are the same. The adapter usually comes with a disposable screwdriver, screws for securing the hard drive and a plastic cover. The latter is needed for installation on an adapter to close the free space that is formed after removing the drive.

Disassembling a laptop

After we have prepared everything you need for replacement and purchased a suitable adapter for the SSD, you can start opening the laptop and then replacing the drive.

This can be done as follows:

  • I turn off the laptop and wait until it turns off completely.
  • Turning over and removing the battery.

After the battery is disconnected, you need to remove the Installed hard drive.

For this:

  • Unscrew the screws and remove the cover on the other side of the battery.
  • In order to remove the cover, you need to pry it off and lift it.

The hard drive and memory modules are located under the cover. We need to remove exactly the hard drive, since a solid state drive will be installed in its place.

If you ask why this is where we Install the SSD, and not instead of the drive, then there is a simple explanation for this.

To properly remove the drive, you must strictly follow the following instructions:

  • We unscrew the screws with which it is fixed.
  • Move the hard drive to the left and carefully remove it from the case.
  • Then we take out the hard drive from the mounting frame and put it aside. We will come back to it.
  • Install the SSD into the mounting frame.
  • After that we install our old hard drive into the adapter. It has a small instruction on how to properly secure the hard drive.

Putting both drives aside, we’ll come back to them later.

DVD drive

Now unscrew the DVD drive. We need a short screwdriver to remove the screw that secures the drive to the case. After unscrewing it, you can remove the drive without any problems.

Then remove the plastic cover from the DVD drive. To do this, you need to open it. This will require a paper clip or needle. We find a small hole on the front panel of the device and insert a paper clip there. After a slight push, the drive carriage will slide out of the case, and you will get full access to its bottom and can easily separate the plug from the carriage.

Once the plug is removed, it will need to be placed on the adapter.

Next, we remove the bracket that attaches it to the laptop from the drive, and rearrange it on our adapter in the same place.

After that, install the adapter in place of the previously extracted drive and tighten the fastening screw.

It remains to turn the laptop upside down and install the SSD disk in place of the old HDD. We close the cover removed at the beginning of disassembly and tighten the remaining bolts around the perimeter of the device, insert the battery.

The laptop is now assembled and ready to go. We installed two hard drives: we put the old HDD into an adapter and connected it instead of a floppy drive, and a new solid-state drive was mounted in its place.

What is needed for installation?

To begin with, you should familiarize yourself with the characteristics of your laptop to understand what components you need to purchase. As practice shows, in most modern models with a CD drive, you can easily install an additional hard disk. Therefore, problems should not arise.

Before starting, you should make sure that you have acquired everything you need to fully work.

You will need:

  • SSD 2.5 form factor “.
  • Tools for disassembling a laptop. Since all screw heads are the same, a small Phillips screwdriver is often required.
  • A plastic pick, a regular bank card, or any other similar item for opening the case. The main thing is that it should be without sharp corners, so as not to damage the train.
  • (adapter, slide) for replacing the drive with 2.5 “.

Special attention should be paid to the last point, so let’s analyze it in more detail.

Instructions for installing an SSD in a laptop instead of a floppy drive

Every user would like to install a modern SSD drive on their PC for better productivity and faster system performance. It is incredibly easy to install a solid state drive on your computer, and the process itself usually does NOT come with any difficulties.

But installing an SSD in a laptop instead of a DVD drive is much more difficult, because first you need to carefully disassemble it. And many users already have difficulties at this stage. So let’s look at the whole process in more detail.

Software settings

The next step is to configure the BIOS, namely to enable AHCI mode. This mode allows you to increase the speed of the drive, mainly due to the advantages of the NCQ technology. Other options are also open, such as hot swapping.

  • We enter the BIOS. Instructions.
  • Go to the “Main” section and set “AHCI” in the “Configure SATA as” option. The section names may differ in different BIOS versions, so try to look for similar settings.
  • Save the “F10” settings and restart the PC.
READ  The laptop charges only when it is turned off

Now you know how to put an SSD in a laptop instead of an old DVD drive, and you can do it yourself without any problems, just following our instructions.

BIOS does NOT display SSD: 3 reasons

  • “Walked away” contact with SATA: you need to open the cover and check if the drive is fully inserted into the slot.
  • The problem is in the SSD drive itself. it happens if you bought a used option, or the drive is long “lying around” idle: checked on another PC.
  • Outdated BIOS: Search and update fix the problem.

The SSD is installed correctly, everything is displayed, but the computer is still weaving like a turtle and “creaks” at opening “Photoshop”? The PC is too old. With a dual-core processor, but with 2GB of RAM and “motherboard”, which was released more than three years ago, there is nothing to hope for. Also, performance will NOT increase if the drive is connected to SATA older than the third version.

The classic method. replacing the HDD

So, the battery is removed, the cover is unscrewed. The time has come to pull out the hard disk: the disk is fastened with a few bolts, they must be unscrewed, and then carefully remove the hard drive from the SATA slot. In this place, you will need to install a solid state drive and secure the SSD with bolts. Final installation steps: attach the cover, place the battery, and turn on the laptop.

During bootup of a laptop (for example, HP 250 G5), the user will need to enter the BIOS. There he will see that the system has detected the SSD. Now you need to check in which mode the disk is operating in the tab called Advanced: if not in AHCI, it will switch the media to this mode and save.

The last step is to install the operating system.

How to connect an SSD to a desktop computer?

Attaching an SSD to a desktop is not difficult at all. To do this, the user will need to de-energize the system unit, and also disassemble it. To get access to the PC components and put in free space or replace the hard drive, you will need to remove the system unit panel.

In some cases, the user will need to parse the entire block. Usually it is required by small-sized models (for example, DELL OptiPlex 3040 SFF).

Life hack: there is a button on the back of the system unit that serves to turn off. You will need to hold it for a few seconds. Do this before disassembling the system unit. In this case, the PC will NOT start, since the device is disconnected from the mains, but such manipulation will remove static electricity from the motherboard, as well as other internal components of the computer.

The SSD drive is installed in the free space using a special adapter, made in the form of a slide and attached with screws. Fasteners are supplied with the drive in the kit. An adapter is required because the form factor of the carrier can be smaller than the dimensions of the slot. For example, the classic tray is for 3.5 ” part, and the most common size for solid state devices is 2.5 “- as in SAMSUNG 2.5” 750 EVO 120GB.

When the drive is delivered, you need to connect the SSD with a SATA cable to “motherboard”, By selecting the corresponding slot on it. Then the SSD should be connected to a power supply, which ensures the smooth operation of all components of the computer.

Important: The drive is fastest only when connected to a SATA 3.0 slot with at least 6 Gb / s speeds. Usually this connector is marked and painted black, so it is not difficult to see it on the board. However, if there are designations, you should find the documents on the motherboard and find information in them in SATA.

When the disk is delivered and the system unit is assembled, the SSD needs to be configured for normal operation of the media. To do this, you need to go into the BIOS, find a solid-state drive there and, if this drive acts in addition to a hard drive, put the SSD first in the list. Thus, SSD will become the main.

As soon as the Installed SSD is the first in the BIOS, you should confirm the changes, and then reinstall the operating system. You can simply copy the OS to the media if there is an HDD or users do NOT plan to leave the SSD as a system disk.

Attention! If the drive will work as a system disk, you should use the classic, preinstalled Windows tools for configuration (usually the system itself optimizes work, which extends the life of the media). When the operating system remains on the HDD, the same disk must be marked in the BIOS as the main one.

How to install an SSD in a laptop?

First of all, the user should create a backup copy of the information that is stored in the laptop. Then. disconnect all wires from the laptop (mouse, headphones and charging), remove the battery by pulling the latches.

To put the drive into a laptop, the user should arm himself with a thin screwdriver and Unscrew the screws that are located on the back cover of the device. They cover the lid that protects the hard drive and laptop RAM.

Life hack: using a plastic card (credit card, discount card), it is convenient to pry off the cover that covers the RAM and HDD.

3 ways to install:

  • Replace the HDD;
  • Instead of an optical drive;
  • “Wise” the method is to put a solid-state drive instead of a hard one, and install a hard one in place of the drive. It is suitable if the speed of the bus to which the old hard drive is connected is faster than that of the drive.

Interesting: if there is no free space for a second data carrier, but you want to leave a hard one, the owner of a laptop has the opportunity to purchase a case for a hard drive to connect an SSD via usb. True, this is only convenient if the laptop is used as a desktop device.

We put an SSD instead of a floppy drive

Preparatory actions Almost do not differ from those described above. So, the user needs to disconnect the laptop from the network and remove the battery. Then, using a screwdriver, Unscrew the screw that holds the cover covering the optical drive compartment.

There is a bolt under this cover that holds the drive. You will need to unscrew it, press the pedal: the drive will slide out of the connector. Now the drive is easy to get.

Important: to install an SSD instead of an optical drive, you need a adapter, which is the same size.

To securely fix the SSD drive, you need to screw four bolts into the drive all the way, put it in the adapter and place it in the SATA slot. A rubber seal will add points to the reliability of fixation.

To prevent the SSD from dangling inside, “” should be fixed in the case. To do this, you need to twist the drive mount and put it into the adapter. The shape of the fasteners is different, but the holes are located according to the standard, so the installation does not have to cause difficulties.

Life hack: so that the connector with the installed SSD (for example, Transcend 370 128GB) does not look artisanal, you can remove the cover equipped with a button from the optical drive. It keeps on latches, which are easy to unfasten with a credit card or pry off with nails. It remains to attach the cover to the adapter and fix it to the body with screws.

READ  Wi-Fi Not Working On Windows 10 Laptop

Difficulties to Face

When installing an SSD or starting a computer / laptop after an upgrade, the user may encounter some difficulties. Most of them are solved at the initial stage.

So, the first thing you should pay attention to when installing an SSD drive yourself (for example, Kingston HyperX Fury 120GB) into a computer or laptop is accuracy. Most housings are made of plastic, so careless actions can damage the skin. For example, the weak point of laptops is the jacks for wires.

Attention! It is better to supplement both a portable and desktop device with an SSD when the computer warranty is over: any upgrade made by the user can “destroy” a guarantee.

If you plan to install an SSD in an optical drive slot, consider the thickness of the adapter. Most models are available with 12.7 millimeters or 9.5 millimeters. To be sure that the adapter will fit, you need to find out the model of the drive and find its characteristics on the Internet.

Solid state hard drive (e.g. SANDISK 2.5 “SATA 3.0 Plus 120GB) is installed, but the device “does not see it?” “- You will need to look into the BIOS again and in the SATA Mode or Advanced item, double-check whether the system is functioning in AHCI. a mode designed to work with SSD.

Consider: in IDE mode, the system recognizes the SSD drive, but some functions that increase the speed of work and increase “life years” hard drive do not work. Therefore, it is worth checking the current mode through the dispatcher. If IDE is set. you need to switch the system to AHCI.

How to properly install an SSD on a computer and laptop? 3 ways

To improve the performance of your computer, as well as get rid of the noise during the operation of a laptop or system unit, an SSD drive comes in handy. a large, fast and silent operation “flash drive”.

Note. The computer will not “hums”, if you only install an SSD. I installed such a device as an addition to the classic hard, the owner of the computer will NOT get rid of the noise, but will speed up the work “cars” and will increase storage.

In the article, we examined the options for connecting an SSD drive to a desktop PC, as well as installing it in a laptop. From the material you will learn what to do to install a solid-state drive and configure the system for the SSD yourself.

Cheat sheet: how to work with an SSD for a long time

Solid-state drives “are not friendly” with high temperatures, so you should think about installing an additional cooler in your desktop computer and working with a laptop on a cooling pad.

SSD manufacturers release firmware updates for devices, which improve performance and extend the life of the drive.

Also, the developers recommend not transferring from a hard one, but installing a new Windows on a solid-state hard drive: versions from seven and “younger” optimize its work automatically.

The article discusses comfortable ways to connect a solid-state drive to a computer and laptop. Such an upgrade will speed up the operation of the device and also reduce noise. The main thing is to do everything neatly and prepare the tools in advance. Please be aware that slot locations and fasteners may vary from device to device.

Watch a detailed video on how to put an SSD in a laptop.

Installing an SSD on a desktop computer

If you have already had experience with installing, connecting or disconnecting a hard drive to a computer, then the procedure for installing an SSD is the same. Again, below we have provided Detailed instructions that describe each step of installing an SSD on a computer:

  • Shut down the entire system, and then Unplug the computer processor from power by pressing the shutdown switch. (Note: Position “O”. disconnected from power supply, position “l”. connected to power supply).
  • Remove the processor cover and then locate the two ribbon cables as in the picture below.
  • Connect the SSD with two ribbon cables. Don’t forget to check the connection reliability.
  • After that, attach the SSD to the processor, if your processor does not have mounts, then use the mount for HDD disks.

After that, start the computer to check the performance and identification of the SSD drive in the system. If the disk is detected in the system, then you can safely proceed to installing the operating system on the SSD disk.

How to install an SSD on a computer or laptop

Installing a solid state drive (SSD) is a great way to significantly speed up your computer. However, many users face installation questions. Therefore, today we will tell you in detail how to install an SSD on a computer or laptop instead of a DVD or hard drive.

Installing an SSD on a laptop

When installing an SSD drive on a laptop, it is important to consider a very important thing. not all laptop models have a special slot for installing an SSD drive. But, this is NOT a problem, since almost every laptop comes with a floppy drive, which we will remove in case your laptop does not have a slot for installing an SSD drive. Again, it is important to note that there are two ways to install an SSD drive on a laptop, which we will discuss below.

Method. Installing an SSD instead of a hard disk drive (HDD)

  • Shut down the system on the laptop and disconnect from charging. Turn the laptop over to gain easy access to the lid.
  • Unscrew the screws and then pry off the laptop cover with a needle or any other object.
  • Unscrew the screw that holds the hard disk drive (HDD), and then carefully remove it from the board so as not to damage the microcircuit.
  • Now install the SSD drive by simply inserting the chip into the laptop board. After that, screw the drive mount and close the lid, and then start the laptop and proceed with the system installation.

Method. Installing an SSD into the “No Removable Hard Disk Drive (HDD)” drive slot

This is a difficult and at the same time the best way to install an SSD drive on a laptop, which does not have a slot for SSD drives. It is worth noting that this method requires a small investment, which will be spent on buying an adapter for an SSD drive. If you agree with this, then you can proceed to the instructions:

  • Unscrew the lid of the laptop in order to gain access to the discarding screws that secure the drive-floppy drive.
  • Then, push the drive casing outward. Be careful, all actions must be done carefully and do not rush.
  • Remove the plastic cover from the drive, to do this, you need to insert pins or a paper clip into the hole on the front of the DVD drive.
  • Now you need to fix the panel from the drive to the adapter, otherwise the laptop will have a pleasant appearance for centuries.
  • Then place the apron in the place where the disk drive was installed. Don’t forget to tighten the screw!
  • Done! Your laptop will now have two storage drives. a hard disk drive (HDD) and a solid state drive (SSD). To speed up the laptop, install the operating system on a solid state drive (SSD), and use the hard disk drive (HDD) to store information.


Attach the removed panel to the adapter, thus preserving the aesthetic appearance of the laptop.

Install and secure the solid state drive dongle adapter in the laptop chassis removed from THESE screws.

It is recommended to reinstall the operating system on a solid-state drive, leave the standard hard drive as storage for data.

READ  How To Connect Laptop Screen To Pc

In general, professionals recommend installing a standard laptop HDD in the adapter, and putting an SSD disk in place of the hard disk.

This makes common sense as the SATA port of the HDD is faster.

As you can see, installing an SSD on a laptop instead of a DVD drive is quick and easy. All business. remove the drive and attach the SSD to this place.

However, there are a lot of benefits from this action. From a weak gadget you create a high-speed, powerful device.

It’s cheaper and more profitable than buying a new laptop. And almost no one uses DVD anymore, everyone switched to flash drives.

Useful articles

Pick up a list of verified, especially relevant, affiliate programs of 2018 that pay money!

Step by step actions

Let’s get started. Unplug the laptop and take out the battery.

If you cannot remove the battery, you need to disconnect it from the main board of the laptop through the connector.

After de-energizing the internal circuits, remove the bottom cover if necessary. On some laptop models, it is enough to remove the drive by unscrewing the mounting bolts without removing the cover.

Unscrew the retaining screws of the floppy drive and gently push it out of the case.

Take your time and be careful. Try to avoid touching the parts of the main board with your hands or a screwdriver.

To remove the plastic cover, press the clip with a needle or a paper clip. To do this, the tool is inserted into a special hole on the front of the DVD drive.

We also remove the special mount for attaching to the case, and install it on the adapter.

Being careful, we insert the SSD into the SATA connector, fixing, installed the standard adapter spacers. Then we screw in the mounting screws through the holes in the sides of the adapter.

There is still a side mount on the drive. we remove it and transfer it to the adapter adapter.

How to install an SSD on a laptop instead of a drive

Before proceeding, you will need to prepare a SlimDVD adapter for it in addition to the SSD.

When choosing, please note that drives differ in size: 12.7 or 9.5 mm, I select it for your gadget.

How to install an SSD on a laptop instead of a DVD drive

If you have a weak laptop, which constantly freezes and downloads a small archive all day, then do not rush to change it. Better read how to install an SSD on a laptop instead of a drive.

For those who want to significantly increase the speed of a laptop, there is an excellent opportunity to replace the DVD drive with a solid-state SSD drive.

The installation process can be complicated only if your laptop model does not have a special slot for an SSD drive. This is solved by removing the DVD drive.

Detaching DVDs

The first step is to disconnect the battery. In cases where the unit is not removable, you will have to remove the laptop cover and disconnect the battery connector from the motherboard.

In most cases, in order to remove the drive, it is not necessary to disassemble the laptop completely. It is enough to unscrew a few screws and the optical drive can be easily removed. If you are not entirely confident in your abilities, then it is better to look for video instructions directly for your model or contact a specialist.

Preparatory stage

Before purchasing such an adapter, you should pay attention to the size of your drive. A regular drive is 12.7 mm high, there are also ultra-thin drives, which are 9.5 mm in height.

Now that we have a suitable adapter and SSD, we can start installing.

Changing DVDs to Solid State Drive

If you have long ago stopped using the DVD drive in your laptop, then it’s time to replace it with a brand new SSD. Didn’t you know that this is possible? Then today we will tell you in detail how to do it and what it takes.

The entire process of replacing a DVD-ROM to an SSD takes a few minutes. As a result, we get an additional disk and new features for our laptop.

How to install an SSD instead of a DVD drive in a laptop

So, after weighing all the pros and cons, we came to the conclusion that an optical drive is already a superfluous device and it would be good to install an SSD instead. To do this, we need the drive itself and a special adapter (or adapter) that will fit perfectly instead of a DVD drive. Thus, it will not only be easier for us to connect the disk, but the laptop case itself will look more aesthetically pleasing.

Installing SSD

Next, prepare the SSD for installation. There are special difficulties here, it is enough to perform three simple steps.

    Insert the disc into the slot.

The adapter has a special socket, has connectors for power and data transmission. It is in it that we insert our drive.

As a rule, the disc is secured with a special spacer and also with several bolts on the sides. We insert the spacers and tighten the bolts so that our device is firmly fixed in place.

Move additional mount.

Then we remove the special mount from the disks (if any) and move it to the adapter.

That’s all, our drive is ready for installation.

Now it remains to insert the adapter from the SSD into the laptop, tighten the bolts and connect the battery. We turn on the laptop, formats a new disk, and then you can transfer the operating system from a magnetic drive to it, and use the latter to store data.

articles on this topic:

What is the switch on this adapter for??

08/26/2018 at 16:43
Asus X555U laptop.
Replaced HDD with SSD.
Everything works perfectly.
I bought an adapter for installing HDD instead of dvd. Installed. System interrupts appeared, loading percent by 15-25%.
I took off the SSD, removed the adapter, installed the HDD in its place. System interrupts are gone.
I installed the SSD in place of the HDD, installed the adapter instead of the dvd (I did NOT install the HDD in the adapter). System interrupts again.
What needs to be done so that the adapter does NOT cause system interrupts? And how is it even possible for an adapter without a device in it to influence something?
Managed to solve the problem.
Found some kind of nameless switch on the adapter hidden with three positions. The instructions do not say anything about him. I turned to the manufacturer what kind of switch it is and in which case what state should it be. They said it was a “rudimentary” switch. It does not affect anything now, everything should work properly regardless of the position of the switch.
I tried all the same to try to experiment and in one of the positions everything worked as it should!
So much for the rudimentary switch. The manufacturer does NOT know what it is producing.
Manufacturer. Dexp.

I also read that SSDs are put in place of HHD, and HHD is already in the drive. Is there a difference?

Center, hello. Yes, there is a difference, but not always. In more or less modern laptops, it often happens that the hard drive is connected via the SATA III interface, and the drive is connected via the SATA II interface. The speed of the first is twice as high as the second, so in such cases it is worth putting the SSD in place of the HDD, and the HDD instead of the drive. The concept of visually, where and what SATA in a laptop, is possible only by the signature, which should be next to the connector for connection.