Laptops and Tablets • Recommendations and advice


How to turn on iPad if it won’t turn on

Table of Contents

Make sure the iPad connector isn’t clogged

Also, quite often the iPad does not charge, and at the same time does not turn on, due to the fact that the charging port of the tablet is clogged. This happens most often on old tablets that have been in active use for several years.

Clean the charging port, for example with a toothpick. It is important to proceed with care and use gentle strokes to remove accumulated debris from the connector. In especially advanced cases, a lot of debris accumulates in the connector, for example, as in the image below:

After cleaning the connector, try charging iPad again. If the iPad does not turn on now, we go to the programmatic ways to solve the problem.

iPad won’t turn on. what to do? 5 ways to solve the problem

iPad is recognized as the best and most reliable tablet. Even older iPads perform well after years of heavy use. However, iPad may experience crashes, for example, the tablet may stop turning on. What to do if iPad won’t turn on? In this manual, we talked about the most effective and efficient ways to solve the problem.

iPad won’t turn on? All the most effective ways to solve this problem are described below. We recommend that you follow one by one from the first to the last. at one of the stages, your iPad will work again!

Check the cable and charging adapter

First of all, you need to make sure that the iPad has stopped turning on, not due to a low battery. Many will be surprised, but often the problem is really that the iPad is completely discharged, but does not charge due to a broken cable or charger.

My iPad Won’t Turn On! Here’s The Real Fix.

Making sure the problem isn’t with the accessories is pretty easy. Try charging another device, such as an iPhone, using the cable and charging adapter. If charging starts, then the accessories are not damaged and you can proceed to the following methods.

Enter iPad into Recovery Mode

The next effective way to solve the problem is to activate Recovery Mode on iPad. Successfully Putting iPad Into Recovery Mode To Bring It Back To Life With iTunes.

In order to enter iPad into recovery mode, follow these steps:

Press and hold the Home button on iPad and connect the tablet to the computer using a USB cable.

Continue holding the Home button until the iTunes logo appears on the iPad.

If the iPad reacted and entered recovery mode, you will have the opportunity to restore the tablet to work.

After entering iPad into recovery mode, you need to launch iTunes. As soon as the program starts, it signals that the iPad is found and suggests updating or restoring the device.

First of all, you need to try to update the iPad, as in this case it will be possible to get rid of the problem without losing data. However, if your iPad has previously been updated to the latest version of iOS, then, of course, it will not be possible to update it.

In this case, all that remains is to select the “Restore” item. After restoring, iPad will start to turn on, but all data on it will be deleted. This method is only recommended if you’ve recently backed up your iPad data.

Hard reset iPad

Let’s start with the simplest way to bring the iPad back to life, which is often a lifesaver. It’s not uncommon for iPad to not turn on due to a software error that needs to be reset. It is very easy to do this. you need to perform a so-called “hard” reboot.

To do this, on the iPad, you need to simultaneously hold down the Home and Power buttons and hold them until the Apple logo appears on the tablet screen (10-15 seconds).

If the Apple logo appears, the iPad is saved! The tablet will turn on and work as before. If the “hard” reboot did not lead to anything, then you should proceed to the following methods.

Restore iPad in DFU Mode

iPad won’t turn on despite all the above methods? Fortunately, the most effective way to solve the problem remains. It provides for putting the tablet into DFU mode and restoring its operation using a third-party utility to fix errors for iOS devices.

iPad won’t turn on. restore via DFU mode

Download the latest version of dr.fone utility from the program’s official website.

Install dr.fone and run the utility. At the same time, it is important to close iTunes, as Apple’s program will interfere with the recovery process.

In the main window of dr.fone, select Repair. The utility allows you to fix various errors on iOS devices, including problems due to which the iPad does not turn on or freezes in recovery mode.

In the window that opens, click Start to start the iPad detection process.

Since your iPad will not turn on, the program will not detect it until it enters DFU mode. In the next window, the utility will notify you of this. click the Device is connected but not recognized button.

In a new window, the program will ask you to enter the iPad into DFU mode. For this:

Press and hold the Home and Power buttons at the same time for 10 seconds.

Release the top Power button, but continue to hold the Home button for another 10 seconds. until the utility detects your iPad.

If you did everything correctly, then your iPad will appear in the utility window:

Note that at this stage, dr.fone utility has the option to launch an interactive tutorial showing how to properly enter iPad into DFU mode.

After successfully entering iPad into DFU mode, click Next.

In the new window, click Download to start downloading the latest firmware for your iPad. The utility itself will download the required firmware version for subsequent recovery.

After the firmware has finished downloading, it remains to press the Fix Now button to start the recovery process. Make sure that the Retain native data checkbox is checked. this parameter is responsible for saving all data on your device.

If none of the above methods helped, then, unfortunately, we are talking about a breakdown of the iPad. over, the breakdown can be absolutely any. only in the service center will help to determine what exactly broke.

Please rate 5 stars at the bottom of the article if you like this topic. Subscribe to us Telegram. In contact with. Instagram YouTube.

Accumulator charging

The first thing you should do when a problem occurs is to fully charge the battery. The battery may be completely discharged, which is why you cannot start your iPhone. Connect the charger along with the cable to the corresponding connector and look at the screen. After a few seconds, the corresponding indicator will appear on it. Below it is an icon indicating that it is connected to a power source.

However, in this situation, the iPhone 4 user may face the following problems:

  • When you press the power key, the low battery indicator does not appear. In this case, you can blame the malfunction of the physical button.
  • When the charging is connected, the corresponding icon does not appear, and the phone screen goes out. There are two options here: a faulty iPhone connector or a cable with a charger block.

Correct switching on with the key

Not all users know how to properly turn on and off mobile devices. Your iPhone 4 may be completely functional, but you are just doing the wrong startup procedure. To turn on the phone correctly, you need to do the following:

  • If the battery is low, connect your phone to a power source.
  • After a while, hold down the power key on the top panel of the device and hold it for 10-15 seconds.
  • As a result, the Apple logo should appear on the screen, and after 30-40 seconds the operating system will boot.

If this option did not help, then test another one: simultaneously hold down the power and Home keys for 10 seconds. Repeat the action several times. If the phone does not turn on, then the reason should be sought in faulty firmware or hardware failure.

Restore via iTunes

If, when you try to turn on the phone, it does not respond or displays an endless boot in the form of an Apple logo, you should use Recover Mode to recover. To complete this procedure, you will need:

  • defective iPhone 4;
  • cable for connecting to a PC;
  • installed iTunes package.

First you need to install the program and driver for iTunes, and then put your phone into recovery mode. To do this, hold down the Home key. Without releasing the button, connect the PC cable to the charging connector.

At this point, iTunes should detect the connected device and display a corresponding notification that the iPhone is in Recovery mode. Using this mode, you can perform a full reset or install the OS firmware. In our situation, it is necessary to reset the device to factory settings. In the device information window, you can back up your personal data to a PC or iCloud. After that, start the procedure with the “Restore iPhone” button.

To install a new version of the OS, you must first download the firmware files to your computer.

If the breakdown of the iPhone 4 was preceded by mechanical stress, water ingress, overheating, etc., then hardware damage is most likely the cause. Take the phone to a service center for diagnostics, but first try to turn it on using our instructions.

How to turn on iPhone 4 if it turned off and won’t turn on

Despite the almost annual release of new iPhone models, many still use old models, up to the 4th generation. Accordingly, due to wear and tear of the device, problems in performance and even normal startup may occur. Today we are going to talk about how to turn on iPhone 4 if it turned off and won‘t turn on.

These tips apply to iPhone models with a Home button. You can fix most of the software problems on your own, but if we are talking about a breakdown of hardware, then you cannot do without contacting a service center.

READ  No charging ipad from computer

We are concluding the guide to restore iPhone 4 and hope that with the help of these recommendations you can easily identify the problem and turn on your mobile device! If you want to clarify any points from the instructions, then ask for help in the comments.

Hardware breakdowns

Hardware faults are much more difficult than system problems. You can diagnose some breakdowns and then repair them.

Press the power button and listen to the speaker of the phone. Your device may have a defective display, but a startup sound is playing. In this case, screen diagnostics are required.

turn, ipad

If you are using an SD card, then try removing it and starting up the device again. The problem may be related to unsupported media or virus files on the memory card.

How to turn on your phone if it won’t turn on

You can face phone breakage at the most inconvenient moment. Therefore, be sure to familiarize yourself with the diagnostic methods and solutions to the problem presented in our article. Today we will figure out how to turn on the phone if it does not turn on.

Factory reset

The next method is relevant for smartphones. It involves rolling back the settings and phone software to the factory state. If the cause of the breakdown is not related to the hardware of the device, then this method will help restore performance.

The reset can be done using a combination of buttons. You need to hold down the Home and Volume Down buttons for a few seconds. After the Recovery menu appears on the screen, you must select the Wipe data / factory reset option. Then the smartphone will start the recovery procedure.

Navigation through the Recovery menu is carried out with the volume keys. The appearance of the menu and the names of the items may differ depending on the firmware version. Also, the methods of launching Recovery differ. check the key combination in the instructions or on the manufacturer’s website.

Remember that factory reset erases all personal data and apps. In order not to lose important information, we recommend making backup copies of profiles, accounts and saving files to cloud services.

Checking the battery and charging

So, you pressed the power button or unlock the device, but there was no reaction. No need to panic. check the basic points first:

  • Connect the charger to your phone. You may have forgotten to charge the battery in time. Wait a while. When charging is active, the corresponding icon should appear on the phone.
  • If this does not happen, try testing the charger’s functionality with another phone. Many modern devices have similar connectors, so you can ask your loved ones for a smartphone.
  • For a phone with a removable battery, open the back cover and check if the battery is installed correctly. This item is irrelevant for most modern smartphones.

Only after a complete check of the battery and charging can you proceed to the next stage. However, you will not be able to make sure that the phone connector is working, so you will have to contact the specialists if our instructions do not help.

Influence of external factors

Another procedure must be followed if the breakdown of the phone is preceded by the influence of external factors. These include water ingress, falls, overheating in the sun, and so on. It is worth noting that the actions in each of the situations are different. For example, if you dropped your phone into the water, then take your time to turn it on. Remove the battery first, if possible. Then place the device completely in a glass or jar of rice. You need to wait a while for all the moisture to come out, and only then turn on the phone. In some cases, this method helps to restore performance.

If we are talking about falls and serious injuries, after which the smartphone stopped turning on, then you must immediately contact the service center.

This concludes the article about turning on broken phones. Follow all the steps from the instructions, and if they do not help, contact the specialists for diagnostics. We do not recommend disassembling mobile devices without proper skills and tools.

Factors associated with battery damage are conventionally divided into three groups:

deformation of the contacts (can occur if the tablet falls into water);

The battery has run out

First of all, if it is impossible to turn on the iPad, it should be connected to the charger. A completely discharged battery is often the reason for this behavior of the iPad. Usually, the battery charge is enough only to display an empty battery, but it often happens that nothing is visible except for a dark screen.

Apple’s minimum recommended charging time is 20 minutes. After that, you need to try to disable it. If the display shows a red battery, the tablet is low and you need to continue charging.

If there are no changes, it is recommended to change the power supply or charger.

Other reasons

Often, even with a loaded battery, iPad still won’t turn on.

There may be several reasons for this behavior of the device:

installation of unlicensed applications and installation of new firmware. A possible solution to the problem is to reinstall the operating system using iTunes. But before reinstalling the operating system, you must try to hard reboot the device;

problems with the elements of the iPad. Most often, the power button breaks. To diagnose such a problem, you need to connect the device to a charger. If the battery charge indicator is displayed on the screen, then the power button is almost certainly out of order;

the charging connector is defective. This type of breakdown is much more difficult to identify, since when you connect the iPad without a charge to charging, nothing happens. A possible way to eliminate this kind of malfunction is to clean the connector contacts;

moisture penetration into the tablet. You can try to deal with this problem yourself. You need to disassemble the tablet and let the device dry for 2-3 days. This method is not always effective and risky, since there is a possibility of board oxidation. Repairing the board is usually quite expensive, and in some cases the device becomes completely non-repairable. In this regard, it is recommended to return the tablet to a service center to fix the problem as soon as possible;

short circuits. Despite the fact that the reason is incredible if used correctly, this can happen when using a non-original charger. The only way out of the problem situation is to replace the burnt out elements.

What to do, iPad has turned off and won’t turn on

Even the highest quality equipment is not immune to malfunctions. And Apple devices that have won the love of users for their functionality and impeccable reliability are no exception.

If your iPad won’t turn on, don’t worry too much. The reason for this is not necessarily a hardware malfunction, most likely the problem is solved easily and trivially.

The reasons for this behavior of the tablet should be determined. This can happen due to a failure of the battery or due to a malfunction of the power button.


The most effective action in the fight against spontaneous shutdown of the tablet is considered to be a hard reboot. To do this, press simultaneously two keys on the iPad “Home” and “Power” and do not release them until an apple (Apple logo) or a graphic image of the battery status appears on the screen.

The appearance of an apple on the display indicates that the problem has been resolved, the tablet is charging and will be available for normal operation.

It should be noted that a hard reboot will reset temporary data.

Recovering the iOS operating system using iTunes

If, after a hard reset, the tablet still does not turn on, then you can try to restore the iPad to work by completely flashing the device.

In order to restore the operating system via iTunes, you will need:

a pre-downloaded file with the version of iOS currently installed on the iPad.

IOS recovery is carried out in the following sequence:

connect iPad to the system unit using a USB cable;

go to the page for setting up device synchronization with iTunes;

while holding down the “Shift” key on the keyboard, click on the “Restore” button;

in the window that appears, select the firmware file;

iTunes will automatically delete all content and download the “fresh” firmware to the iPad‘s internal memory. After the update, the device will be transferred to Recovery Mode, and the device will be restored to the factory state.

iPad stuck on apple and won’t turn on

The situation when an Apple tablet does not turn on, and an apple is on the display is quite common. The likely source of the problem is a software malfunction. To solve it, you need to install a new firmware of the tablet using iTunes.

In addition to a software problem, the reason for this behavior may be hardware. In case of malfunction of the internal components of the tablet, you cannot do without the help of third-party specialists.

In general, when an apple appears on the screen, you shouldn’t worry too much, most likely, nothing critical has happened to the tablet, and the problem can be solved on its own. However, in extreme cases, such as moisture getting inside the device, it is better to contact the service center.

Typically, if an Apple tablet turns off and does not turn on, it means that there was a power failure in the device. In this case, the tablet can independently turn on or off, periodically changing the battery charge level indicator. Usually, with such problems, replacing the battery helps, even if the gadget was purchased recently.

Only experienced specialists can accurately answer the question of what to do when the iPad does not turn on. Timely contacting a specialized service center will help to avoid more serious problems and unnecessary costs.

What to do if iPhone won’t turn on?

The iPhone is not an eternal device, although it fails a little less often than Android, but still it is not uncommon, then the question arises of what to do if the iPhone does not turn on. Gadgets often break down, freeze and stop responding to user actions. Often the reason is mechanical or external damage to the device, but this is not always the case.

IPhone 4, 5, 6, or 7 won’t turn on. power adapter

A fairly common problem that the iPhone 5s does not turn on is a power failure situation. The user, even when connected, may not see any reaction of the smartphone, but often they do not even suspect about such a banal solution to the problem as charging.

The iPhone owner needs to connect it to a charger, no matter what power source: 220 V, car or computer. Do not be alarmed if there is no immediate reaction. With deep discharge, for example, when the phone freezes, it takes time for the charging indicator to appear. It is worth waiting at least a few minutes, usually this time is sufficient. It is better to put it on charge for 1 hour, and then try to turn it on, do not forget about the previous method, it is still applicable now. Sometimes the process does not start, this can provoke various mechanical problems.

  • Check the cleanliness of the connectors, remove all kinds of foreign objects and dirt with a needle or brush;
  • Make sure that there are no kinks in the wire, probably there are interruptions;
  • Check the tightness of the contacts, perhaps the wire does not enter completely, then you will have to determine the reason for this;
  • We strongly recommend using original chargers. Lightning cables from Chinese manufacturers overheat during operation, may have insufficient power to charge or practically no power;
  • Sometimes the power or charging controller fails, then you will have to use the services of a service center.

iPhone Shut Down and Won’t Turn On. Force Start

If the iPhone 5s turns off and does not turn on, you should use the function that forces the smartphone to start. The method is relevant for those cases when the smartphone is frozen at some stage, perhaps only a black screen is shown, but the backlight is working, or after turning it off, the phone stops turning on. In this case, the procedure does not clear the device data, so it should be used initially. For each version of the iPhone, there is the same key combination, only in the latest 7th model it is different:

  • Hold down the Home button and the Power button at the same time. The hold time should be more than 10 seconds, usually up to 20 seconds. Then the Apple logo appears on the screen in the form of an apple. This option works for all versions except iPhone 7;
  • A separate, more familiar approach is used in the new version, you need to hold Power and the volume control, namely the volume down button. Similarly, you need to hold until the action on the screen begins.
READ  How to turn off redmi AirDots headphones

The problem can be fixed by this method, but there are several additional methods.

Why iPhone won’t turn on?

It is not worth thinking about why the iPhone 5 and any other model does not turn on for a long time if it was externally exposed to unwanted influences:

  • Perhaps the smartphone was dropped into the water, even a short-term immersion or rain can provoke a short circuit and refusal to work. If the phone was really drowned, you should not turn it on right away, on the contrary, turn it off and put it off to dry. After 1 day, try to turn it on, so the probability of restoring its work is higher, otherwise a short circuit will occur at startup and the smartphone will be unusable;
  • Mechanical damage. An iPhone, falling from a height, often takes a hit on the display, and the insides are less likely to suffer. There is no way out except to give the smartphone for repair;
  • Freezing. Batteries are afraid of prolonged exposure to frost, and at one point they lose all their charge due to a chemical reaction. You need to warm it up in your hands, and then try to start it, most likely you will have to charge it.

In these cases, it is possible to eliminate the malfunction only at service centers. There are a number of other reasons that lead to a freeze, some of which can be easily eliminated.

How to turn on iPhone if it won’t turn on?

It happens that the iPhone charges, but does not turn on, especially often it reaches the logo and freezes at this moment or turns off. In this case, you can apply recovery mode. To use it, you need to have a computer at hand. It is highly desirable that the iPhone has already been connected to it beforehand, and the PC has been added to a trusted source of the connection, but this may not be useful.

  • Connect your smartphone and computer;
  • Launch iTunes;
  • Perform a forced restart of the device. Home (for the 7th version, the volume down button) and Power;
  • A message will appear on the computer screen allowing you to restore the operation of the iOS system, you should click on “Update”.

In this case, an attempt will be made to install the operating system without erasing files. You may need to completely restore your iPhone to factory settings. Then in iTunes you will have to go to the main tab and click “Restore”.

turn, ipad

Ultimately, if iPhone 6, iPhone 7, or any other version still won’t turn on, you need to contact technical support. They will remotely provide instructions on how to fix the problem, if this does not help, then they will direct you to the service center closest to you. This will mean that the problem is of a technical nature and the user is powerless here.

If the smartphone was used with care and charged with original chargers, then most likely it will be possible to restore its operation using the described methods. Otherwise, you will have to give the device to experts.

No votes yet! Be the first to rate this post.

How can you fix a software glitch?

If a tablet from Samsung, Lenovo or another brand does not turn on, but the user knows for sure that the device did not fall or suffered from any other kind of damage, it is worth performing 3 procedures.

When working with a computer or laptop, it is the restart of the system that helps the technician to get out of the “stupor”. The same technique works for the tablet as well. To reboot it, you need to hold the power button for 10-15 seconds, then try to start the tablet again.

You might be wondering: How does a tablet differ from a laptop

Has nothing changed? Then the second option:

  • find a small button or a hole with the inscription Reset on the case;
  • take a thin object (pin or paper clip), and gently press the button;
  • withstand up to 15 seconds.

Try to turn on the device. Perhaps it is after these steps that the tablet PC will start.

Important! The Reset button is not available on all tablet models. Often only state employees are equipped with such an element.

The new tablet does not turn on, but there are a minimum of options, what to do? The same reboot will come to the rescue. The new device does not have a large amount of accumulated information, and therefore the whole process will take a couple of minutes.

Settings Failure

To reset all tablet settings (for example, such as Huawei MediaPad T3 10) to factory settings, you need to activate the Recovery program. It is launched by a certain combination of buttons, but which ones, each manufacturer decides at its discretion.

The most popular ciphers:

  • turning on the volume (add);
  • reduce the sound side power button;
  • Power Home reduce sound;
  • sound start home.

One of these configurations will work 100% and enable the required software. After the tool is launched, information similar to the one in the picture below will appear on the screen. Using the sound adjustment button, the search is directed to the line “wipe data / factory reset”. To press it, Power is used.

Next, an inscription will light up, which will warn that due to such a “hard” reboot, all downloaded data, personal information, contacts, etc. will be deleted. You can save some of the information by removing the SIM card and flash drive beforehand.

Now click Yes and wait for the procedure to complete. After a factory reset, the tablet will turn on by itself (tested on Lenovo Tab M8 HD 2/32 LTE).

Using Safe Mode

This technique will be effective if it was possible to start the tablet, but its work leaves much to be desired: constant lags, system freezes, and more. To eliminate all interference with the normal operation of the device, use the safe mode.

You can enter it by opening the settings menu of the tablet PC. press the “Power off” button. hold it. It will ask if the user wants to go to Safe Mode. It must be confirmed that yes. The next field will open, in which you can delete all unnecessary files, installed programs and applications that cause incorrect operation of the device. And to update the system, you just need to restart the device.

Software errors

When the visual diagnostics of the tablet did not reveal chips, cracks, blurring on the screen, other defects and the likelihood of hardware failures completely “disappeared”. we can assume that the cause of the breakdown lies in the software component.

In this case, the tablet may not turn on due to:

  • Defects the device with malicious viruses or codes.
  • Malfunctions of the downloaded software.
  • Damage to the operating system or individual applications.
  • Incorrect operation of the basic settings of the gadget.

It is not easy to determine which item from this list has brought chaos to the tablet program, but you can try to reanimate it with a few simple steps.

Hardware failure

The problem lies in the equipment itself, that is, there was a breakdown of some element or the contacts came off. The most common causes of hardware failures are:
“Ripped” micro USB slot;

  • connecting incompatible or non-working devices to the tablet (the same charge);
  • any damage to board elements;
  • “Fuse” or “hung” the power button itself;
  • the battery life has come to an end;
  • the loop of the screen inside the tablet has disappeared.

The first thing to do is to find a 100% working charge, connect it to a tablet (for example, to a Samsung Galaxy Tab S5e 10.5 T725 LTE) and leave it there for 2-3 hours. After such manipulations, even those gadgets whose battery was very badly discharged and the power controller has already disconnected it from the charge circuit often “come to life”. You can check if the battery is charging by touching the power supply: it must be warm or hot.

If the miracle did not happen, and other ideas on how to start the tablet, if it does not turn on, did not arise in my head, the only way out is to contact the service center. If your tablet is still under warranty, you can get a free repair. The exceptions are cases where there is mechanical damage or contact with water.

What to do if the tablet does not turn on. 2 possible problems and 3 ways to solve them

Do you know the situation when, when you turn on the tablet, it simply refuses to work, still remaining Malevich’s black square? The sensations of the user in the first seconds after that. a panic fear of the possibility of a serious breakdown. But you should not despair, because most of the problems of tablet devices can be easily solved, you just need to understand the nuances of the device. So why the tablet may not turn on and how to fix the situation? The article offers detailed instructions for a home repairman.

The tablet does not turn on: possible problems

All mini-laptop malfunctions boil down to two problems: a hardware failure and software troubles. To be able to independently, if not “revive” the tablet (for example, an ASUS tablet that does not turn on), then at least understand the cause of the breakdown and what to do, it is worth understanding each of the factors.

The tablet turns on, but does not boot

If the touch device shows “signs of life”, but the matter did not go beyond the logo on the screen, the reasons may be very different. The table below shows the most common ones:

Tip: To avoid data loss in case of possible tablet malfunctions, it will not be superfluous to regularly back up the most useful information. You can transfer files to the cloud or any other selected device.

Reset the machine to factory settings

If after trying to turn on the smartphone does not respond at all or the screen lights up, but the device does not boot, try restoring factory settings using the hardware buttons.

Remember: during a system reset, you may lose personal data that has not been synced to the server. Do not do this if you are afraid to erase important information.

turn, ipad

Take out the battery and put it back

If your phone has a removable battery, remove the cover and slide the battery out of the device. Wait at least 30 seconds and replace the battery. Then try to turn on the phone in the usual way. using the power button.

How to Force Restart iPhone

On iPhone 8, iPhone 8 Plus, or later, hold down and immediately release the Volume Up key and then the Volume Down key. After that, press and hold the side button until the Apple logo is displayed.

On iPhone 7 or iPhone 7 Plus, hold down the Side key along with the Volume Down button for 10 seconds or more until you see the Apple logo.

On iPhone SE, iPhone 6s, iPhone 6s Plus or older, hold down the Home key with the Side button for 10 seconds or more until the Apple logo appears.

Force restart the device

Your phone may be on, but just frozen. In this case, the screen may be dark and unresponsive to any actions. So first try restarting your device using the hardware keys.

Put your phone on charge

Connect your phone to a wall outlet using the original charger. If within an hour the charging indicator does not appear on the display and you cannot turn on the device, check the integrity and cleanliness of the connector, as well as the condition of the power cable and adapter. Try different sockets if possible, replace cable and / or adapter.

READ  How to transfer files from computer to ipad

What to do if your phone won’t turn on

Do not rush to take your smartphone for repair. Perhaps these simple steps will help revive the device.

If problems arise due to water getting into the device, do not connect it to the mains and stop pressing the buttons. Dry your phone as soon as possible and only then follow the advice in this article. If you are sure that the inside of the smartphone is dry, feel free to continue.

How to force restart an Android smartphone

Press and hold the power button and volume down key at the same time for 10-15 seconds. If successful, the device will restart automatically or display a menu on the screen in which you will need to select the restart command.

To reboot some Android smartphones, just hold down the power button for a few seconds. Sometimes there are gadgets that are restarted using other keys. If the smartphone does not respond to the listed actions, type in the search engine the query “how to force restart” and add the name of your model. Then follow the instructions found.

How to reset iPhone to original settings

First of all, connect your phone to your computer using the original cable. If you have a Mac with macOS Catalina, launch Finder. If you’re using an older version of macOS or Windows, start iTunes. If it is not installed, download it from the Apple website.

Then force restart your iPhone (see step 1). When you see the Apple logo, continue to hold the buttons until the recovery mode appears on the smartphone screen.

Immediately after that, a window with further instructions should appear on the computer monitor. Click “Update” and follow the system prompts.

iTunes will download the correct software for your phone. If this process takes more than 15 minutes, the iPhone may exit recovery mode. In this case, hold down the forced restart buttons again and hold them until the device returns to this mode.

If the update works, the phone may turn on without resetting the system. If not, then in the iTunes window, click “Restore” to restore the factory settings.

Turns on and freezes after the splash screen

Sometimes, for some reason, the laptop does not start in any way. And sometimes it still starts, you can see the initial splash screen and basic information about the device on the screen, and then the device freezes. Either nothing happens at all, or information appears about errors that interfere with the full operation of the machine.

  • Don’t be intimidated. The most common reason for this is the BIOS settings. You just need to enter the BIOS and reset all parameters. “Load BIOS Defaults”. After that save and exit.
  • Sometimes it happens that the laptop freezes, reports the detected error and asks to press a certain button. For example, “Press F1 to continue”. As a rule, after pressing it, it continues to turn on and then works as usual. And although such a solution to the problem is the simplest, you should not ignore the very fact of reporting an error. Most often this happens if the battery in the motherboard of the laptop starts to run out or the BIOS settings get lost. Please note that you need to contact the service center to replace the battery.
  • Of course, problems with a laptop can be more serious. For example, malfunctions associated with the operation of the hard disk manifest themselves in a similar way. In this case, there is a chance to determine the presence of problems by ear. If the hard drive is faulty, then you will hear the engine trying to start unsuccessfully under a slight crackling of the heads.
  • Another reason why the laptop won’t turn on is RAM. Some device models provide access to its brackets. You can try removing them and gently cleaning the contacts. If this does not help, then start the machine, leaving only one memory module at a time. In the event that your device has only one bar, then put it in another slot and start the device again. There is a great chance that these actions of yours will help solve the problem.

What to do if the laptop does not turn on: 6 main situations and ways out of them

No one is safe from laptop breakage. But the good news is that most of the problems that arise in the operation of this device can be solved. It is only necessary to determine the cause of the breakdown and its nature, and then act according to the situation. All laptop problems are either software or hardware. It is necessary to accurately diagnose the malfunction, and then you will already know exactly what steps to take to eliminate it.

So, why the laptop does not turn on and what to do?

The laptop constantly reboots or turns off

If your device is constantly shutting down and rebooting, then it is most likely a serious hardware problem. Perhaps the fault is in the short circuit in the south bridge, which caused it to overheat. Or, dust has gotten into the cooler, which has caused excessive heating inside the processor. If so, the fan will run at high speeds, but it will still not cope with the problem. As a result, your laptop will periodically shut down and reboot. This will happen at a variety of times, regardless of external reasons. You are unlikely to be able to solve the problem yourself this time, so immediately contact the service center.

But before that, make sure it’s not a bad diet. If the laptop battery runs out, the device can turn on and then immediately shut down.

Coolers can be heard, but the laptop screen is not working

So, you know what to do if your laptop won’t turn on. But there are also cases when it starts, but its screen remains dark. What to do in this case?

Take a close look at the monitor. Perhaps you still manage to consider something? If so, then the screen, most likely, is in order, but the backlight does not work. You can enable it using the hotkeys on the keyboard. Each model has its own and most users are well known.
2. Another way to check if the screen is working is to connect an external monitor to the laptop. If a picture appears on it, then there is no doubt and the cause of the malfunction is determined.
3. Often the problem is hidden in a discrete video card. This element sometimes overheats and breaks down. By the way, some video cards are prone to breakdowns more often than others. For example, nVidia graphics cards have a short lifespan.

To prevent such damage, do not hold the laptop on your lap or in any other position with the ventilation holes covered. It is advisable in such cases to use special stands that do not impede air circulation.

If your laptop is not a gaming laptop, then do not devote too much time to games on it. And one more thing. do not forget to monitor the temperature of the video card. If the reason is in it, then remove or simply turn it off. on some laptop models, switches are specially provided for this. With the missing discrete video card, your device will continue to work, you just have to temporarily say goodbye to some games.

Of course, the reason why the laptop boots and won’t turn on can be more serious. For example, in some cases, the problem is with the processor or firmware, motherboard or memory. But you are unlikely to cope with such difficulties on your own.

The laptop does not turn on and shows no signs of life

The worst thing that an ordinary user of this device can imagine. What to do in this case?

  • Often, if the laptop does not start, then the problem lies in its power supply. Therefore, first of all, check if there is a light in the house and voltage in the outlet.
  • If there were no problems with electricity, you should proceed to inspect the power supply. Perhaps it began to work intermittently, or it broke completely. The surest way to be sure of this is to get the exact same power supply, only in working order. Connect it to your laptop and see if your device turns on.
  • Often the breakdown of the power supply is very trivial. broken wires or broken contacts in the connectors. By the way, in the future, one simple rule will help to avoid problems with the charger. When charging the laptop, first plug the plug into the device, and then plug the adapter into an electrical outlet. The fact is that with a different connection order, a spark appears, which spoils the contacts.
  • If a similar power unit does not save the situation, then it is time to move on to more decisive actions. Remove the battery from your device, wait 10-15 minutes, and then turn on the device. If it turns on without problems, then secure it and put the battery in its original place.
  • Another reason why the laptop does not turn on, sometimes lies in the devices connected to it. Disable them all, including even the Wi-Fi adapter. Try to start the device again. If the laptop turns on, then return the external devices one by one to understand which one triggered the problem.

These are the steps you can take yourself when your laptop won’t boot. If none of them led to the desired results, then the problem should be looked for in a non-working motherboard, broken internal contacts and more. And only an experienced master will help with this.

A message is displayed about the inability to start from the boot device

As a rule, we are talking about a variety of messages in English. If you are faced with this, then remove all flash drives from the device, and remove the disk from the drive. Restart your laptop. If your actions have not brought any positive result, then the problem most likely lies in the work of the hard disk. Such a malfunction can be of both software and hardware nature.

In the first case, reinstall Windows. If after that your laptop began to work as before, then this means that the problem was software and now it has already been resolved. If reinstalling the operating system did not save the situation, then it’s time to contact the service department, whose employees will solve this malfunction at the hardware level.

After loading Windows shows the screen of death, errors on the black screen and reboots

Another fairly common problem is when, when you turn on the laptop, Windows starts to load, but then the boot is interrupted, and the device restarts. The screen turns blue or black and displays numerous error messages.

As in the previous case, the problem can be of both software and hardware nature. And again, restarting Windows will help to understand what exactly happened to your device. Reinstallation of the operating system can be started from a bootable flash drive. If you succeed in doing this, then the problem can be considered solved. If not, then you can’t figure it out without the help of specialists from the service center.

Thus, if the laptop does not turn on, then this is not a reason to panic. In many situations, you can diagnose and fix the problem yourself. You just need to analyze your recent actions with this device. For example, if you spent many hours playing a game shortly before the breakdown, then your video card is most likely overheated. Try a little and you will be able to bring your device back to life again.