How to turn on ASUS laptop without a button

3 ways you can turn on your laptop and sleep mode without the power button

Any, even the best laptop is not immune from the most common problem faced by users. breakdown of the power key. Of course, if this problem occurs, you should contact the technical service for repair. If there is no such possibility yet or an urgent start of the computer is required, the question arises. how can you turn on the laptop without a working power button? There are several methods to start the laptop in a different way.

Hardware button to launch Boot Menu

Most laptops are equipped with an emergency power button that brings the PC into the Boot Menu. The main models equipped with this function are Lenovo, Sony, Acer, Asus, HP.

turn, asus, laptop, button

To use this option, inspect your computer for a similar button. The main places where it can be located are next to the Power key or to the side of the keyboard. It looks like a small circular depression.

Once the key you want is found, follow these instructions:

  • The hardware button can be hidden deep in the panel, so you won’t be able to activate it by pressing your fingers. To activate, you need to press on it with a sharp object (needle, toothpick, pin).
  • The screen will light up a blue screen, find the “Normal stantup” command and click on it.
  • Confirm the action by pressing the Enter key. Next, the usual Windows boot will begin.

With this simple method, you can turn on your laptop and continue working. However, if your computer is from Dell, DEXP, or Samsung, your search for a hardware button will not be successful. It is not provided on these models.

Power ON in BIOS

Using the BIOS menu, you can assign a specific key combination to start the laptop. After this procedure, the performance of the main Power becomes not particularly important.

To perform this operation, follow the instructions:

  • Enter BIOS (press the F2 key after starting the laptop).
  • After booting the system, look for the command “Power Management” in the continuation of “Setup” or “Power”, depending on the model.
  • In the menu that opens, select the “Power on function” command (these are the system power settings) or “Power On by PS2 KB / MS”.
  • Then click the item “Any Key”, after “Hot Key”. now you can set the desired combination on the keyboard with which you will start Windows.
  • Press F10 to confirm the settings. Enter.

Reboot your laptop. Now, to turn on the system, you just need to click on the selected combination.

The way for professionals. directly from the motherboard

The next method is suitable for those who, at least at a basic level, understand the PC device. This option is to close contacts, which leads to the activation of Windows.

In order to understand how to open the motherboard, look at the instructions for your laptop.

Usually, it is enough to pry off the protective cover next to the Power button with a flat object; this is done quite easily. Next, you need to close the contacts with a screwdriver.

If fixing the Power button is postponed for some time, you can bring the startup cable out of the laptop case. This will allow you to close the contacts whenever you want, without opening the protective case every time.

Tip: If your laptop is under warranty, do not use this method.

Before using the above methods, make sure that the reason for the lack of Power response is precisely in the start button. The malfunction may be different:

  • If the laptop has a completely discharged battery, then no method will help. The device needs to be charged.
  • Possible problem could be a faulty power supply or cable.
  • Broken or damaged motherboard.

Sleep mode

You can also just not turn off the laptop, but leave it in “sleep” mode. To install this mode, follow the instructions:

  • Follow the chain: Start. Control Panel. Power supply.
  • On the left, select “Sleep Settings”.
  • Now you need to set the sleep time for mains and battery operation. Opposite the line “Putting the computer into sleep mode” set the desired time.

To get Windows to wake up from sleep, follow these steps:

  • Follow the chain: Start. Control Panel. Device Manager.
  • Click on the “Keyboard” icon with RMB, select “Properties”.
  • Go to the Power Management section.
  • Put consent next to “Allow this device to wake up the computer”.
  • Apply settings.

With new settings, the laptop will go to sleep after a certain amount of time. Pressing any key on the keyboard will help you get the computer out of this mode.

Turning on the laptop without the power button

The most diverse switches have never been classified as highly reliable devices. This fully applies to such a control as the laptop power button. It so happens that it is impossible to turn on the device using the standard method. Before configuring the system for activation in other ways, it is worth excluding possible power problems. If all else fails, it is possible to configure the laptop to turn on without pressing the power button. This is done in different ways depending on the model.

BIOS setup

Most modern mobile devices allow you to change the power button of your laptop. Simply put, the system can be started using the keyboard. To make the necessary settings, you need to get into the BIOS. To do this, you will need to turn on the laptop without the power button in one of the above ways.

  • the BIOS searches for the Power Management section;
  • there is a Power On Key item;
  • one of the suggested values ​​is set, except for the previously set one.

Some BIOS versions allow you to set your own, unique combination of buttons to enable using the keyboard. After selecting the Save and Exit section, the Exit and Save Changes item, the settings will be saved. The laptop will reboot and can henceforth be turned on without the power button set by the key combination.

Launching from the motherboard

Unfortunately, many laptop models do not have a hardware boot menu entry button. These are Dell, Samsung and many others. You can’t turn them on without the power button. But the problem can be solved by adjusting the BIOS. But to enter it, you will need to disassemble the device case.

But even without such a cheat sheet, everything can be done correctly. The main thing is to act carefully and slowly. Before work, you should stock up on thin screwdrivers and a knife.

  • The laptop is disconnected from the mains, the battery is removed from it.
  • Bottom panel covers are removed.
  • The bottom panel is completely released. To do this, a thin blade is led along the line of joining the parts, finding the latches and squeezing them sequentially. Some laptops do not have to work so hard, because their bottom panel is attached to other parts of the case with screws.
  • On the motherboard, a contact block with wires attached to it is found. Most models call it F-Panel, JFP1. The corresponding name is printed on the surface of the motherboard.
  • According to the symbols on the block, the contacts PWR SW, PWR SW are found-.
  • To turn on the laptop, it is enough to short-circuit them once with a screwdriver.

It is possible to supply power to the hardware by closing the contacts only when the laptop is assembled and the adapter or battery is connected. Therefore, this method is suitable for models in which you can remove the cover on the front panel above the keyboard to access the power button. It is easy to visually find here two contacts for closing. A loop from the button leads to them. Also, the option is suitable for laptops, where access to the contact comb on the motherboard opens after removing the service hatches on the bottom.

If disassembling the laptop is difficult, and it is impossible to save all the connections, it is recommended to bring the terminals to the outside for closing. To do this, you can use thin wires or remove a completely similar, regular pair of cables from an old desktop PC case. They are immediately equipped with terminals for easy installation on the motherboard comb.

Checking Power System Problems

If the button does not work and you cannot turn on the laptop, first of all you need to make sure that there are no problems with external devices. They may be as follows.

  • The battery is discharged or damaged. The battery must be removed. After that, the power button is pressed while the laptop’s network adapter is on.
  • The power cable is damaged. The study of the wire should be carried out only with the adapter disconnected from the network. If the insulation is damaged, there are areas of free bending, which means a cable breakage. repair or its complete replacement is required.
  • The power adapter is not working. This assumption can only be checked by connecting another voltage conversion unit to the laptop.
  • The connection connector is worn out. This can only be verified experimentally. The plug must be wiggled in the socket and at the same time press the power button.

It will not be superfluous to check the parameters of the outlet. Perhaps there is simply not enough tension. When bundled with a missing or discharged battery, this results in the laptop not responding when the power button is pressed. If the checks show that the power supply system is in order, then it is necessary to reconfigure the way of switching on.

As a conclusion

If the laptop power button is broken, it is recommended to contact the service to replace the cable or switch. Usually this kind of work is not expensive. Self-repair in the form of cutting a broken loop, replacing a switch with a compatible one with a lack of experience can lead to a violation of the electrical parameters of the hardware. Sometimes this is accompanied by a breakdown of the motherboard and results in extremely expensive repairs.

By correctly organizing the switching on of the laptop without pressing the power button, it is easy to operate the device without inconvenience. over, this will take place as normal. But it is still worth replacing the button or loop. This will allow the mobile device to return to its full, manufacturer-intended convenience and functionality.

Launch via hardware boot menu button

Some laptops Lenovo (very often), Acer, Asus, HP (very rarely) are equipped with a hardware button to enter the BIOS. In some Sony series, there is also a hardware key in the group above the keyboard, which launches the maintenance wizard.

READ  Wi-Fi Not Working On Windows 10 Laptop

If it is present, press the boot menu start button. This may require a pen or needle. For some models, the button is hidden and only a thin hole leads to it. Here the item Normal Startup is selected. The operating system then starts up normally. Having a button to enter the boot menu, you can easily turn on the laptop without the power button.

The best laptops according to customers

Laptop Apple MacBook Air 13 with Retina display Late 2018 on Yandex Market

Laptop Xiaomi Mi Notebook Air 13.3 ″ 2018 on Yandex Market

Lenovo ThinkPad Edge E480 laptop on Yandex Market

Laptop Acer SWIFT 3 (SF314-54G) on Yandex Market

Laptop Acer ASPIRE 7 (A717-71G) on Yandex Market

We start the laptop without the power button

We do not recommend disassembling the laptop and trying to fix the button if you have never worked with such equipment before. Failure to do so can damage other components. Better to use the services of a professional or turn on the laptop without a button. Sometimes only the top of the button breaks, while the switch remains intact. To start the device, you just need to press the switch with any convenient object.

Launching a laptop without a power button

A broken power button on a laptop is a common problem for many users. This situation leads to the inability to start the device. It would be most correct to fix the button, but it is not always possible to do this manually or immediately take it to a service center for repair. You can start the device without this button, but this is done in two simple ways.

Boot Menu

Almost all modern laptop PCs are equipped with a special button that allows you to launch a special menu. Most often it is located somewhere on the side of the case or at the top near the display and is pressed with a finger or a needle. You can turn on the laptop using it as follows:

    Examine the case of the device carefully or look for the description in the manual to find the button you need.

Press it once and wait for the menu to launch. A small blue window should appear on the screen. Navigate through it using the arrow keys, select “Normal Startup” and press Enter.

After a while, the operating system will boot successfully. Of course, you can use this button all the time, but it is not always convenient and causes some difficulties. Therefore, it is better to set certain parameters through the BIOS. Read more about them below.

Power ON function

It is better to take care of how to turn on the laptop in advance if the start button breaks. In addition, this method will be useful for those who start the system through the Boot Menu. You just need to set certain parameters, and you can turn on the laptop from the keyboard. Follow the instructions:

Go to the Power Management Setup or Power section. Partition names may vary depending on the BIOS manufacturer.

Find the item “Power ON function” and set the value to “Any Key”.

  • Now you can reboot the device, just do not forget to save the settings before exiting.
  • Thanks to the change in this parameter, the laptop can now be started by pressing absolutely any key on the keyboard. After fixing the Power button, you can return the reverse settings in the same way if this configuration does not suit you.

    Today we have analyzed two options, thanks to which the mobile computer is turned on without a corresponding button. Such methods allow you not to disassemble the device for manual repair and do not urgently carry it to a service center for repair.

    Another option is Power ON function

    The next method requires changing the settings in the BIOS.

    To enter the BIOS, press F2 or del. These keys work on most laptops, netbooks, including ASUS. On Lenovo, acer can be used f1, on Sony. escf2.

    But these keys are useless if the laptop won’t turn on.

    • press the hardware button;
    • included in the boot menu;
    • choose BIOS setup.
    • find the power menu item (power management setup);
    • go to power settings. power on (power on by ps2 kb / ms);
    • specify the way how the laptop should be turned on. If you select “any key”, the activation will be performed using any key. Pressing the “hot key” selects any key combination. The option is not available on all PCs;
    • press f10, save and exit.

    After rebooting, the laptop can be started by pressing the hotkeys set in the BIOS.

    We start the laptop with a faulty power button using our method and keyboard

    Hello dear readers! A common problem in laptops is the power button stops working. It blinks, does not turn on, does not respond to pressing. It is not always possible to take the device to the service immediately after detecting a breakdown. There are several ways to turn on the laptop without the power button from the keyboard. Each of them will be described in detail in our article.

    The most difficult method is to start from the motherboard

    Configuring the entrance to a laptop with a disabled power key through the BIOS is an easy-to-configure, convenient way for further use. The only drawback is that in order to use it, you must first log into the laptop. A hardware button is used for this. If it is absent, it is launched from the motherboard.

    • disconnect the laptop from the network;
    • remove the battery;
    • remove the bottom panel of the case. Carefully inspect the bottom of the laptop, unscrew the screws. If this is not enough, draw a thin plastic knife or a plastic card around the perimeter of the device at the junctions of the lower and upper parts of the case. If you find the latches, gently squeeze;
    • find the block of contacts on the motherboard. The surface says jfp1 or f-panel;
    • find pwr sf /. or pwr;
    • close the contacts with a screwdriver;
    • assemble laptop.

    To disassemble the laptop with your own hands, it is difficult to find contacts on the motherboard. What should a beginner do? It’s easier to close them on a non-working button.

    • remove the panel above the keyboard. If it is absent, remove the keyboard. Dismantling starts from the top. With a screwdriver or knife, the latches are sequentially squeezed out, lifting the freed corners;
    • find the board on which the contacts are located. It is enough to trace where the trains lead;
    • check if the cable is working properly by disconnecting it, short-circuiting the contacts. In the event of a malfunction, replacement is required;
    • with a working loop, close the contacts with a screwdriver, a thin metal object. Instead, they remove the button, bring the closure terminals outward using thin wires, cables from an old PC;
    • assemble the laptop. Clicking the fasteners, install the keyboard, replace the battery.

    To disassemble a laptop, close contacts, you need knowledge, experience, a complete understanding of the sequence of actions. If you are not confident in your abilities, do not know the pinout schemes, take your laptop to a service. There, the faulty part will be replaced, repaired. If the problem lies in the cable, you need to change it to a new one, fix the old one.

    The easiest way is Boot Menu

    Power button problem is a common laptop malfunction. The key has sunk, does not respond to pressing for a long time, after switching on it immediately goes out, blinks. There are many reasons why the button broke. Our task is to start the device without it.

    The boot menu is used to start the laptop. Its main purpose is the ability to select a device to boot Windows. A file on a hard disk, flash drive, disk can be used. To enter the boot menu on laptops there is a hardware button.
    You can find it on the models of the following manufacturers:

    • sony;
    • lenovo;
    • asus;
    • acer;
    • HP.

    The location differs depending on the model. On some it is on the side, on others. under the keyboard, above it.

    Samsung, dell, desp button is missing.

    • look through the body of the device and look for buttons. If not, read the instructions. what if they missed it;
    • press the button. If it is hidden in the body, use a pin or needle to press it. One click is enough;
    • a small blue window will appear. Select the normal operating mode. normal startup, click enter.

    The laptop will start up. It is inconvenient to follow the described procedure each time. It is better not to turn off the laptop, but to configure the transition of Windows to sleep mode and the ability to exit from it.

    There are several ways to enable hibernation:

    • press “start”, then. “sleep”;
    • go to PC settings, click “systems”, select “power and sleep mode”, determine the time when the inactive laptop falls asleep;
    • go to the control panel, where to find the “power supply”, set the settings for the transition to sleep mode.

    To turn off sleep mode, use the mouse or any key on the keyboard.

    Setting up the output via the keyboard is done as follows:

    • open the device manager;
    • select the “keyboard” menu item;
    • right-click, select “properties”;
    • go to “power management”;
    • check “allow this device to wake up the computer.

    Now you can wake up the laptop from sleep mode by pressing any key on the keyboard. They use the built-in as well as an external keyboard connected via USB.

    Another option to make the PC turn on is to use the mouse.

    • press start;
    • open the device manager;
    • select “mice and other devices”;
    • by clicking the right mouse button go to properties;
    • select “power management”;
    • grant permission to turn off standby.

    There are several ways to forcibly turn on laptops with a disabled power button. The most difficult and time-consuming one requires disassembling the laptop, closing the contacts. We advise only professionals to use it. For everyone else, at the first attempt, we recommend entering the boot menu using an additional button. In BIOS, configure the inclusion of a laptop from pressing any key or combination, configure sleep mode, the ability to exit it from the keyboard. As soon as possible, go to the service, repair the malfunction.

    We activate Wi-Fi with a button on the case

    There are laptops in which the manufacturer embeds a separate Wi-Fi button for convenience. But on older models, instead of a button, there may be a small slider. Therefore, you have to carefully inspect the entire case for the presence of a button or slider. If you find it, try to turn on Wi-Fi, and if not, then read the second option below.

    READ  How to turn on Wi-Fi on an HP laptop

    How to check the laptop power button for a malfunction

    To make sure that the power button on the laptop does not really work, you need to diagnose it.

    To do this, follow a series of steps:

    • Disconnect the device from the network;
    • We disassemble the laptop. To do this, turn it over, remove the battery, unscrew all the screws on the case, disconnect the bottom cover;
    • We carry out a visual inspection of the button. In most cases, the button is very simple: two contacts are closed when you press on the convex metal diaphragm. Very often, dust accumulates under it, and the contacts themselves become covered with a layer of oxide over time. As a result, when you press the button, the contacts are not closed;
    • We call the button. To do this, put the needle tips of the tester on the two contacts of the button and press it. When the button is pressed, the device should emit a characteristic sound signal. If this does not happen, the button does not work;
    • We clean the contacts under the metal diaphragm of the button. With tweezers, carefully remove the upper part of the button and use a contact cleaner to remove traces of oxide and other contaminants;
    • Putting the button together and retesting it. In most cases, cleaning the contacts allows you to restore the functionality of the button without replacing.

    Putting into sleep mode

    At the time of a breakdown, so as not to suffer every time you turn it on, you can simply not turn off the laptop. Put it to sleep while not using it. And when needed, press any key or move the mouse, and the system will immediately “wake up”.

    • Open one by one “Start” “Control Panel” “Power supply”.
    • In the left column, select “Setting the transition to sleep mode”.
    • In front of the line “Put the computer into sleep mode”, set the time twice, for example, 5 minutes. when running on battery and mains.
    • Click on “Save Changes”.

    Now you have to configure the conditions for waking up from sleep mode.

    • Click “Start” “Control Panel” “Device Manager”.
    • Right click on the word “Keyboard” by selecting “Properties”.
    • Go to the Power Management menu.
    • Check the box next to “Allow this device to wake up the computer”.

    Now you can return the laptop to work from sleep by pressing any button on the keyboard. In approximately the same way, you can configure the wake-up from the sleep state using the mouse.

    ASUS LAPTOP HOW TO POWER ON IF THE POWER BUTTON IS DEFECTIVE

    Power ON function

    It is better to take care of how to turn on the laptop in advance if the start button breaks. In addition, this method will be useful for those who start the system through the Boot Menu. You just need to set certain parameters, and you can turn on the laptop from the keyboard. Follow the instructions:

    turn, asus, laptop, button

    Read more: How to get into BIOS on a computer

    Go to the Power Management Setup or Power section. Partition names may vary depending on the BIOS manufacturer.

    Find the item “Power ON function” and set the value to “Any Key”.

  • Now you can reboot the device, just do not forget to save the settings before exiting.
  • Thanks to the change in this parameter, the laptop can now be started by pressing absolutely any key on the keyboard. After fixing the Power button, you can return the reverse settings in the same way if this configuration does not suit you.

    Contact closure

    If the hardware login button is completely absent on your device, you can try to close the contacts. To do this, you will have to make a partial disassembly.

    If the laptop is under warranty, it is best not to resort to this method.

    The essence of your actions will be as follows: you need to disconnect the broken button and connect the PWR and Ground contacts bypassing it.

    How to disassemble your laptop, see the documentation. After all, the models are very different from each other. Usually, it is enough to remove the protective cover near the keyboard by prying it with something thin, and you will get access to the coveted button. Try shorting the contacts with a screwdriver on the board itself. Or you can, by disconnecting the cable from the motherboard, do it right there.

    There is also a third option: bring the cable out of the case. The next time you need to work, close the contacts.

    Do not rush to ruffle the laptop. First, make sure that the problem of not turning on is really in the broken button. After all, a laptop may not work for other reasons. For instance:

    • the battery has run out;
    • damaged power cable;
    • the power adapter is broken;
    • the processor flew;
    • defective motherboard, etc.

    Only by discarding all other options and making sure that the power key is faulty, proceed to closing the contacts.

    The most difficult method is to start from the motherboard

    Configuring the entrance to a laptop with a disabled power key through the BIOS is an easy-to-configure, convenient way for further use. The only drawback is that in order to use it, you must first log into the laptop. A hardware button is used for this. If it is absent, it is launched from the motherboard.

    • disconnect the laptop from the network;
    • remove the battery;
    • remove the bottom panel of the case. Carefully inspect the bottom of the laptop, unscrew the screws. If this is not enough, draw a thin plastic knife or a plastic card around the perimeter of the device at the junctions of the lower and upper parts of the case. If you find the latches, gently squeeze;
    • find the block of contacts on the motherboard. The surface says jfp1 or f-panel;
    • find pwr sf /. or pwr;
    • close the contacts with a screwdriver;
    • assemble laptop.

    To disassemble the laptop with your own hands, it is difficult to find contacts on the motherboard. What should a beginner do? It’s easier to close them on a non-working button.

    • remove the panel above the keyboard. If it is absent, remove the keyboard. Dismantling starts from the top. With a screwdriver or knife, the latches are sequentially squeezed out, lifting the freed corners;
    • find the board on which the contacts are located. It is enough to trace where the trains lead;
    • check if the cable is working properly by disconnecting it, short-circuiting the contacts. In the event of a malfunction, replacement is required;
    • with a working loop, close the contacts with a screwdriver, a thin metal object. Instead, they remove the button, bring the closure terminals outward using thin wires, cables from an old PC;
    • assemble the laptop. Clicking the fasteners, install the keyboard, replace the battery.

    To disassemble a laptop, close contacts, you need knowledge, experience, a complete understanding of the sequence of actions. If you are not confident in your abilities, do not know the pinout schemes, take your laptop to a service. There, the faulty part will be replaced, repaired. If the problem lies in the cable, you need to change it to a new one, fix the old one.

    How to turn on a laptop without a power button

    Broken power button is one of the most common problems for laptop users. This fault prevents the device from starting in the usual way. It is best to repair and replace the button, but it is not always possible to do this at home or immediately take the laptop to a repair shop. You can turn on the device bypassing this button, and you can do this in several ways.

    How can you turn on a laptop without a button

    It is not advised to disassemble the laptop on your own and try to fix a button that does not work, if you have not worked with such devices before. Incorrectly performed actions will lead to breakage of other elements.

    It is best to use the services of specialists or turn on the device without a button. In some cases, only the top is broken, and the switch is in working order. To start the laptop, you will only need to press the base of the button in any available way.

    Boot Menu

    Almost all laptops have a dedicated button that, when pressed, allows you to activate a special menu. As a rule, it is located on some side of the case or on top of the screen and is pressed with a needle or finger. You can turn on the device in this way by observing the following steps:

    How To Turn On Laptop Without Power Button || Turn On Laptop With Phone

    • Look closely at the laptop case or look for the description in the user manual to determine the required button.
    • Find a needle or pin if installed in the body itself.
    • Press once and wait for the menu to open. A small blue window should appear on the monitor. Moving around the window with the keyboard arrows, find the “Normal Startup” mode and then press the Enter key.

    After a certain time, the laptop will turn on successfully. Naturally, this button can be used all the time, but it is sometimes inconvenient and causes certain difficulties. Therefore, it is advisable to make certain settings in the BIOS.

    Power ON function

    It is better to first take care of how to turn on the laptop if the start key is broken. In addition, this method is useful for people who start using the Boot Menu. It is only necessary to specify certain settings, and it will be possible to turn on the device from the keyboard.

    • Go to BIOS in any way.
    • Find the “Power” menu. The name may be different depending on the BIOS manufacturer.
    • Find the “Power ON function” submenu and set “Any Key”.
    • Next, you need to restart the laptop, but you must save before exiting.

    By changing these settings, the device can be turned on by pressing absolutely any button on the keyboard.

    What other ways are there to turn on a laptop without a button

    Some laptops are not equipped with keys to enter a special menu. Turning on the device will not work without it. But the launch can be done from the motherboard through the BIOS. To get to it, you need to disassemble the laptop case.

    Turning on the laptop for the first time

    Before using the laptop, you must first connect the power supply (adapter) to the corresponding connector in the laptop case. Have you connected? Now plug this power supply into a power outlet. The LEDs on both the adapter and the laptop should light up. So, everything was done correctly. Hurrah!

    READ  Keyboard backlight won't turn on on asus laptop

    Feel free to open the laptop lid. By the way, when opening, hold the laptop lid in the middle, or both corners at once. Otherwise, for example, when opening at one corner, the lid hinges may loosen over time, and this will not lead to anything good. This must be done with both hands. Hold the top cover in the middle with one hand and the bottom cover with the other. So you will reduce the load on the LCD matrix, which will significantly extend the life of the loop cable. It is also advisable to place the laptop on a hard and flat surface, so that the air flow will constantly flow to the ventilation grill.

    You can work on a laptop without a mouse, using a touchpad (touch panel). But, believe my experience, it is much more convenient to use a mouse that needs to be connected to any USB port.

    Find the power button, it is located directly under the screen. As a rule, this is the central button, to the left and right of it there may be buttons for turning on the touchpad and Wi-Fi.

    Press the power button. The second (blue) indicator light will light up, the power button itself will light up.

    If you did everything correctly, the process of loading the operating system will begin: first, an image and an inscription will appear on the monitor screen, informing that Windows is starting. Then a bunch of different letters and numbers will flash before your eyes; then a “Welcome” window will open and at the end of this performance a window with a desktop will open in front of you with musical accompaniment.

    During the first boot, several windows may appear in which you will need to enter some information. For example, the name under which you will work on the laptop, preferred language (select Russian), time zone, etc.

    To check, slide your finger across the touchpad, the cursor should move. If it doesn’t respond, the touchpad is disabled. To turn it on, press the button next to the power button, a hand can be drawn on or next to the touchpad. In the off position, the touchpad button can be illuminated with an orange indicator. After entering all the data, the system will save them, you will see the Windows 7 desktop.

    How to properly shut down your laptop

    There are several ways to shut down your laptop.

    • Traditional shutdown. Start. Completion of work. In Windows XP, the operating system will specify what action needs to be performed, and only after a second confirmation will turn off the laptop. In Windows 7, the PC will shut down without further questions. In this case, all open applications will be automatically terminated, the data will be saved. The shutdown itself will take about a minute, restarting it will take a few minutes, which will take to load the operating system, check executable files with the antivirus, etc.
    • Power off using the Power Indicator button, which is usually located under the monitor. This button, if configured to shutdown, allows one short press to correctly turn off the laptop while preserving all the parameters of the previous session.
    • Closing the laptop lid. With certain settings, closing the lid puts the PC into sleep mode. In this case, the work of the programs need not be terminated. After turning on (short press on the Power indicator button), the work of all unfinished programs will continue, with the exception, perhaps, of the network connection. When plugged in, the laptop can be in sleep mode for a long time, and if you use it constantly, hibernation will allow you not to turn off the computer at all. If the battery runs out during sleep mode, the laptop will quit all applications and turn off automatically.
    • Shutdown using the CtrlAltDel key combination. The method is indispensable in cases where the laptop does not respond to user commands, that is, “freezes”. A single press of this combination brings up the Task Manager, a second press leads to a reboot.
    • Forced disconnection of the laptop. This method cannot be considered correct, you have to use it when the laptop completely “freezes”, the keyboard is blocked and does not respond to any user commands. You can de-energize the laptop by long pressing the Power indicator button. In the most extreme case, you will have to disconnect the laptop from the network and remove the battery for a few seconds.

    © 2003. 2020 The Wild Truth. all rights reserved, reprint of articles is prohibited

    Input device

    Before moving on to drastic measures, let’s discuss how to turn on the laptop without the power button from the keyboard. This option exists, but it needs to be configured in advance while the device is still working well. To activate the required function, go to the BIOS. To do this, press the Delete button continuously. The BIOS menu appears. We use arrows to work with it. If we have an HP laptop, go to the Power Management Setup section. We open the power settings. To do this, use the Power on Function item. In some BIOS models, the required function may be called Power On by PS2 KB / MS. Next, we indicate the method for turning on the laptop. To make it work with one key, select Any Key. We confirm the changes with the F10 key and press Enter. To enable activation by means of a specific button, instead of Any key, select Hot Key. We indicate the most suitable keyboard shortcut. Apply changes with F10.

    If the laptop no longer turns on, and the previously described settings have not been made, it is impossible to activate it from the keyboard, so skip to the next section of this material. It describes a step-by-step process for solving the problem.

    Launch

    The laptop model does not really matter when using this manual, since the basic elements of different laptop computers are similar. We turn on the laptop. To do this, using tools with insulated handles, we connect the wiring together. We use pliers or a screwdriver. Thus, it will be possible to avoid an unpleasant and painful electric shock. There are cases in which the button is pressed and is in its place, but the laptop for some reason does not want to turn on. Here it is especially necessary to understand the reasons. This situation can be caused by minor malfunctions and major breakdowns. In the first case, the problem can be eliminated by hand. Sometimes starting does not occur because the battery or the connection cord has been damaged.

    Tools

    So, let’s get down to a direct discussion of the question of whether it is possible to turn on the laptop without the power button and how to do it. To begin with, we need the following tools: a soldering iron, neutral flux, electrical tape, a screwdriver and pliers equipped with an insulated handle, a tester. Situations are different, for example, if an HP laptop is used, the “start” button can get stuck in the plastic panel. This often happens with devices from other manufacturers. In any case, the laptop is useless in this state. First of all, we clarify whether the warranty period at the service center has expired. The fact is that we have to disassemble the device, which will make further free repairs impossible.

    Disassembly

    In order to figure out how to turn on the laptop without the power button and why it “refuses” to work, we remove the battery. As soon as the battery is removed, proceed to the next step. The laptop model is of great importance here. It depends on it where the power button is located: on the case, on the side, near the keyboard, on the panel above. Let’s start with the last option. If the button is located on the top of the panel, we need a neutral flux, a screwdriver and a soldering iron. Carefully pry off the bezel. For this we use a screwdriver. Next, we solder two conductors, thereby bringing them up. To do this, we drill two holes on the top panel. This is required as it is not recommended to use an open device. We install the panel in place. We perform all actions carefully so that a short circuit does not happen.

    Details on how to turn on the laptop without the power button

    Now we will look at how to turn on the laptop without the power button. There are situations in which it is necessary to bring the device into working condition urgently. However, the trigger button at this moment may “refuse” to work. Let’s try to figure out what to do in a similar situation.

    Until the last screw

    Now let’s look at how to turn on the laptop without the power button, if the element of interest to us is located on the side of the case. In this case, we disassemble the entire apparatus. We start with the display. We remove the caps from the mounts on it. Next, let’s move on to the keyboard. Disconnect it. We unscrew all the screws from the bottom cover, remove the top one. We get access to the very place to which the button is connected. Solder two parallel conductors under neutral flux. We bring them out. We assemble the laptop in the opposite order. We connect the battery last, as well as the mains cable.

    External elements

    We check the outlet for voltage. If it is present, disconnect the cord from the laptop and check it on the connection. If the problem is caused by the battery, remove it and connect the device directly to a power source. We perform similar actions with a special device. a tester. When replacing the battery, disconnect the laptop from the power source.

    It is much more difficult to solve problems with starting the device if the damage has touched the basic I / O system, video card or microcircuits. In this case, it is possible to determine the cause of the breakdown only with special devices. oscilloscope or probes. This will have to be done at the service center. Another problem that only experts can solve is the unexpected freeze and failure of the restart button. Now you know how to turn on your laptop without the power button.