How to Switch Graphics Card on an Amd Radeon Laptop

Windows standard tool

To force the switch to discrete graphics, you must manually disable the integrated graphics adapter and then restart the device. As a result, the laptop will start working on a discrete card. the maximum level of performance will be provided, but at the same time, power consumption will increase.

Disabling the integrated adapter is performed through the “Device Manager”, you can get into it through the “Control Panel” or by right-clicking on the “Start” menu. In the list you need to find the “Video adapters” section, right-click on the integrated graphics chip and select “Disable”.

This item should not be used if only one video card is displayed in the “Video adapters” list. this means that the discrete device is deactivated through the BIOS (we will talk about how to enable it later).

You can switch to a productive video card and make it work on a permanent basis through the BIOS menu. This requires:

  • Reboot the PC and press the key that is responsible for calling the BIOS during startup. Delete or one of F1. F12 can act as such a button. The specific key can be seen on the start screen or found on the Internet by the laptop manufacturer.
  • In the BIOS menu, find the “Config” or “Advanced” tab.
  • Find the item “Graphics Device” and set the value corresponding to the discrete AMD card. Changes are applied by pressing F10.

After rebooting, the laptop will automatically start working on the discrete graphics card, ignoring the presence of the integrated graphics chip.

Manufacturer software

AMD has developed a special software designed to manually control video adapters from this manufacturer. Usually it is installed from the factory in the system. if the program is available, you can download it for free from the official website.

The sequence of actions when working through special software is as follows:

  • Launching the Catalyst Control Center utility.
  • We find the section “Power” and go to the block “switchable graphics adapters”.
  • We set the “High performance” mode if we want the laptop to always work on a discrete video card.
  • Additionally, you can set specific parameters for different applications. In the list “Application settings for switchable graphics” select the program or game of interest and set the value “High performance” in the drop-down list.

We also recommend that you study this video tutorial. it clearly demonstrates the process of managing two video cards on laptops.

Switching video card

There are several working ways to switch the graphics adapter. All of them are presented in the list below:

  • Using the system tools provided by the OS developers.
  • Laptop Configuration Utility. BIOS.
  • With the introduction of special software produced by the video card manufacturer.

How to switch AMD Radeon graphics on a laptop

Most laptops come with two graphics solutions at once. Integrated (or integrated) graphics are designed to save power while performing simple tasks. The discrete option comes into play when running heavy games and programs. In this article, we will look at how on a laptop it will switch the AMD Radeon graphics card to a discrete video chip if the switching is not done automatically or if you need to forcefully improve performance.

Switch between graphics adapters to ensure maximum performance in heavy applications and save energy when watching a movie on the go.

Manufacturer software

AMD has developed a special software designed to manually control video adapters from this manufacturer. Usually it is installed from the factory in the system. if the program is available, you can download it for free from the official website.

The sequence of actions when working through special software is as follows:

  • Launching the Catalyst Control Center utility.
  • We find the section “Power” and go to the block “switchable graphics adapters”.
  • We set the “High performance” mode if we want the laptop to always work on a discrete video card.
  • Additionally, you can set specific parameters for different applications. In the list “Application settings for switchable graphics” select the program or game of interest and set the value “High performance” in the drop-down list.

This method is preferred if the discrete graphics chip is correctly displayed in the device manager and is equipped with all the necessary drivers.

How to switch the graphics card on an amd laptop

How to change the video card on a laptop through the device manager

The second option, how to switch the video card on a laptop, is to use the Windows Device Manager tool. This menu contains all the system elements that are installed on the laptop. You cannot change the configuration here, but you can disable some of the devices. To go to the panel, do the following:

  • Right click on the “My Computer” icon.
  • Select “Management”.
  • In the left menu, find the line “Device Manager”.
  • Expand the item “Display adapters”. It contains the chipsets that are installed in the system.
  • Right-click on the built-in adapter, select “Disable”.

Such manipulation will turn off the extra chip and only one main chip will remain. This is a temporary measure because the device will restart after restarting the computer. To switch the startup priority forever, you should use the specialized software that comes with the AMD Radeon, Nvidia GeForce adapters. This way of changing the priority is much safer and easier.

device Manager

In Windows it is possible to change the active video adapter using the device manager. If the settings show two cards, for example, NVIDIA GeForce and Intel, just right-click on the integrated video adapter and name it “Disable”. Such a solution will simply turn off the screen on the laptop. You can turn it back on by rebooting.

READ  Do I Need To Constantly Keep My Laptop On Charge

The method is used for rare purposes by users who know exactly what result they want to achieve. Using this trick is not recommended if you are using a laptop at a simple user level.

Using programs for working with a video card

In the process of installing drivers for a discrete video adapter, special programs are also installed that allow you to configure the operation of a particular element. These programs are called Catalyst Control Center and NVIDIA Control Center.

The required item for NVIDIA cards in this program is called “3D Settings”. The program itself can be launched if you right-click anywhere on the desktop and select NVIDIA Control Panel. Another way is to find it in the tray, near the clock. The procedure for switching looks like this:

  • Select the item “Manage 3D parameters”;
  • Click on “Software settings”;
  • Add the desired exe file. To do this, we will write a path to it by selecting the “Add” parameter.

Now, when starting the game, the system will switch you to a discrete video adapter.

Using the Catalyst utility developed for Radeon / AMD cards with an Intel processor, you can also switch the cards from integrated to discrete. It is enough to find an icon with this program in the system tray and name it by it. Then select Switchable Graphics under Power. The next step is to specify the path to the file, which should run on another video card (item “Other applications”). The AMD VISION utility has been developed for Similar cards running under the control of an AMD processor. You can find it in the lower right corner near the clock. Everything is extremely simple here:

  • Select “Performance”;
  • Click on Dual Graphics;
  • Click on “Disable”, save changes.

Switch between graphics adapters to ensure maximum performance in heavy applications and save energy when watching a movie on the go.

How to switch between video cards on a laptop

For those who do not know what a video adapter is in a laptop, you need to remember that at the moment two types of this element of the system are used. The first one is built into the processor, the adapter cannot boast of high performance, but it consumes little power. PC models with this combination are generally cheaper. There are models of such processors in both world manufacturers: Intel and AMD.

The second type of video adapters is discrete or separate. These cards are well suited for gaming, video processing, but are more expensive, have higher power consumption and run hotter. It is not necessary that the system has only one type of graphics chip. Many laptop computers have both types of adapters at the same time. By default, the operating system itself makes the choice which of them to launch in a given task. Sometimes it makes mistakes and needs customization.

If the video adapters are of the same generation and from the same manufacturer, you can set the parameters under which they will work at the same time, increasing the performance of the computer. However, game developers recommend choosing one basic option. This can be done with:

  • Task manager;
  • In the BIOS;
  • Special programs.

Proprietary software

When installing drivers for Nvidia and AMD video cards, proprietary software is installed in the system, which allows you to configure the adapter parameters. In green it is the GeForce Experience application containing the Nvidia Control Panel, and in red it is AMD Catalyst Control Center.

To call a program from Nvidia, just go to the “Control Panel” and find the corresponding item there.

The link to AMD CCC is located in the same place, in addition, you can access the settings by right-clicking on the desktop.

As we know, the hardware market includes AMD processors and graphics (both integrated and discrete), Intel processors and integrated graphics, and discrete Nvidia accelerators. Based on this, four options for the layout of the system can be presented.

  • AMD CPU. AMD Radeon GPU.
  • CPU AMD. GPU Nvidia.
  • CPU Intel. GPU AMD Radeon.
  • CPU Intel. GPU Nvidia.

Since we will be setting up an external video card, there are only two ways left.

    A laptop with a Radeon graphics card and any integrated graphics core. In this case, switching between adapters occurs in the software, in which we talked a little above (Catalyst Control Center).

Here you need to go to the “switchable graphics adapters” section and click on one of the buttons indicated in the screenshot.

Laptop with discrete graphics from Nvidia and built-in from any manufacturer. With this configuration, the adapters are switched in the Nvidia Control Panel. After opening, you need to go to the section “3D Settings” and select the item “Manage 3D Settings”.

Next, you need to go to the “Global parameters” tab and select one of the options in the drop-down list.

Switching the graphics card in a laptop

Many laptop models today are NOT inferior to desktop computers in processing power, but video adapters in portable devices are often not productive for centuries. This applies to embedded graphics.

The desire of manufacturers to increase the graphics power of the laptop leads to the installation of an additional discrete graphics card. In the event that the manufacturer has NOT bothered to install a high-performance graphics adapter, users have to add the necessary component to the system on their own.

Today we’ll talk about how to switch video cards on laptops that have two GPUs.

The essence of the problem

It should be noted right away: the problem appears when the drivers or the operating system are configured incorrectly. In other situations, it is extremely difficult to face it. She occurs in the following situations:

  • Installing an unsupported OS on a laptop. The problem is especially relevant with the advent of laptop lines that run Windows 8 and higher. Due to the fact that Windows 8 was an outright failure and is hated by users, many seven have installed. The problem manifested itself quickly: there were no drivers for the required OS and we had to look for workarounds;
  • Violation of the order of installation of drivers. It is imperative that the drivers are installed on the laptop in a strict order. This is often neglected even by experienced service engineers. If you put the driver on the video card to how the chipset driver will be installed, the problem will not appear immediately, but after a while. The order is always Fixed and will be described later;
  • BIOS malfunction. In rare situations, due to a BIOS chip failure, a discrete (AMD Radeon) video card simply turns off and has to be turned on again. The solution may be to replace the battery with the BIOS, or replace the microcontroller itself (however, not every service center can do it).
READ  How To Find Out How Many Inches A Laptop

The decision often depends on which of the mistakes was made in the process. Therefore, you need to be able to identify the source of the problem. For example, a BIOS malfunction is diagnosed as follows: if the GPU turns off only when the laptop is turned off, then the problem is related to the microcontroller.

Note: Integrated and discrete graphics cards will often be mentioned hereinafter. AMD Radeon is discrete, that is, separately connected. It is not sewn into the processor, it is located on a separate section of the motherboard and has its own cooling (often the radiator covers both the PC and GPU).

Serial Driver Installation

When setting up Windows, you need to install drivers in a strictly defined order. Some manufacturers (for example, HP and Acer) even mark the archive names with numbers on the website. These numbers suggest the order of installing the drivers.

But, these firms are rather an exception to the generally accepted rules to sign drivers “anyhow”. But, before setting up the software part, you should remember the main algorithm:

Chipset. Integrated graphics card. Discrete graphics card

This order is extremely important. Devices on the motherboard will be recognized with errors without installing the chipset drivers. And without connecting an integrated video card, it will not be possible to configure a discrete one. If the installation order is followed, all other steps will be easier. Violations Possible crashes, up to a black screen after restarting the computer as a result of adding Radeon to the system.

Note: The driver for a discrete video card must be taken from the manufacturer’s website. That is, for an Acer laptop, you need to look for a driver on the Radeon website, not Acer. It should also be remembered that laptop video cards have the letter “m” at the end.

Switching methods

There are several main ways that help to rearrange the main video adapter to the required one. They depend on the OS version, on the laptop model and even on the installed additional software. Therefore, we consider options as the complexity or risks increase.

switch, graphics, card, radeon, laptop

Configuring AMD Control Center

The same action as the previous one can be done using AMD Control Center. This is a program that comes and is installed along with the driver, if you take it from the website of the video card manufacturer, not the laptop. The program itself has several convenient ways to set this configuration. But it’s best to duplicate it for each game separately. This is called “control over the application”.

Note: some games, for example, The Elder Scrolls Online, are able to ignore the system settings and stubbornly work with the integrated video chip. When configured through AMD CC (or Catalyst Control Center, as it was called earlier), even these games are given up.

Switching graphics card on amd radeon laptop

Laptops have various specific problems. One of them is a real disaster for many gamers.

In laptops using Radeon GPUs as a more productive GPU, there is a problem with the connection of the latter. We disassemble how to switch the video card on a laptop amd radeon.

Extreme switching

An extreme option is to disable the integrated video card in the “Device Manager”. Having opened the latter, you need to select video processors and mark the integral.

In the screenshot, for example, an NVidia video card is used, and the integrated one is turned off altogether through the BIOS. She’s even on the list. But by selecting a device and right-clicking on it, you can select the “Disable” item and the unnecessary device will be clothed from the system. Then programs will run only with AMD Radeon graphics.

Switch from app

Windows 10 introduced an option such as “Run with GPU”. This means that you clicked on the program shortcut with the right mouse button, you will notice the following term.

This line displays the graphics devices available on the system. AMD Radeon can be selected from this list and will immediately launch the program along with this GPU. This solution is the simplest and most convenient for users, but does not always appear in the list.

BIOS shutdown

You can remove the integrated video card in the BIOS. This will require:

  • Reboot laptop.
  • Start pressing “Esc” or “Del” (or, other options, depending on the version of the laptop itself).
  • Go to the “Chipset” section.
  • Set “Integral VGA” (or other similar item. In the screenshot it is “Integral Graphic Mode”) to “Off”.

Thus, the device will not even be displayed in the list and it will be possible to use only the Radeon video adapter.

Switching nVidia

The nVidia card drivers contain the Control Panel utility. It allows you to set the default to use a discrete accelerator for any application. To enable 2 video cards, you need:

  • Name the left mouse button on the free space of the desktop;
  • From the menu that opens, select nVidia Control Panel.

If the card software is completely installed in the user, the control panel icon is already in the tray. To access the settings, to enable the discrete graphics card on the laptop for the application, you need to name the icon with the right mouse button and select Open.

In the left part of the window, you need to name it the 3D Settings section. Here, on the Software Settings tab, you can specify the application that should use the discrete adapter. It is enough to select it and click the add button. If you change the default video card in this way, it is enough to launch the game so that it starts using the productive graphics accelerator.

READ  Laptop Won'T Boot What To Do

Disable Device Manager

If the laptop has 2 video cards, and it runs on Windows XP, it is NOT possible to select the main one by software. The easiest way is to disable one accelerator in Device Manager. To do this, you need to enter it in one of the following ways:

  • Press WinR and enter the command devmgmt.Msc;
  • Click Start-Control Panel, switch to Large icons display mode, launch the System and press the dispatcher button;
  • Right-click on Computer, select Manage, click on Device Manager in the left column.

In the list of system devices, just expand the Video adapters section. To make a discrete video card the main one, you need to disable the second.

On another video card, its name in the list of devices, you need to right-click. In the menu, just select Disable and confirm your actions. A reboot may be required. If the image on the laptop screen disappears. to turn off, just press and release the power button. Correctly configured operating system will shutdown.

Do the same if you need to turn on the 2nd video card, which was previously disabled. Again you need to go to Device Manager, right-click on the adapter name, select Enable or Enable from the menu.

As a conclusion

The above switching methods always work with correctly installed drivers and correctly working cards. If something does not work out, it is worth checking the status of the devices in the manager. When the yellow triangles appear next to the adapter names, the correct driver set must be installed first. And then no configuration problem, either by means of the operating system or by the utilities of the adapter manufacturer or through the BIOS, will simply arise.

Switching the graphics card on a laptop

Most modern laptops are equipped with two video cards. Integrated saves energy and works when performing normal office tasks, surfing the Internet or watching movies. Discrete AMD Radeon or nVidia is only enabled in games. The problem is that the system doesn’t always do it automatically.

There are methods how to manually switch the video card on a laptop. This can be done using both drivers and operating system tools. The most drastic way is to change the BIOS settings, where you can force the system to turn on the desired mode.

Driver switching

This method works both in the popular seven and in the newest version of Windows 10. All video card manufacturers offer a proprietary set of drivers bundled with hardware. It is with the help of the bundled software that you can switch between video cards.

What to do if the video card does NOT switch

There are situations when the video card does NOT switch, and after blocking by the device manager, the image on the screen does NOT appear at all. In this case, it is worth adjusting the BIOS settings. Most motherboards allow you to choose the main integrated graphics card, work in switchover mode, or force the system to use only a discrete video accelerator.

How to enter the BIOS. you should look in the documentation for the laptop or on the Internet for the name of its model. The methods differ in products from different manufacturers. On HP laptop, Del, F10, F2 buttons are used. In Sony, you need to press the hardware Assist key to turn it on. Lenovo SEPARATE series models have a small round button at the end, closer to the rear of the keyboard assembly.

Motherboards support multiple adjustment options.

  • Init Display First with option Int, PCI. Here you can install either one or the second video card as the only one used. In Int / PCI and PCI / Int modes (if supported), you can set the order of cards initialization. This is useful if the screen goes blank after disabling the adapter in Device Manager.
  • Integrated Graphic Adapter with PEG, IGD options and combinations thereof. This setting is similar to the previous one. Only discrete card (PEG), only integrated card (IGD) can work, or the order of their initialization can be specified.
  • Graphics Driver. Depending on the hardware platform of the laptop, there may be a different set of options. At Lenovo, it’s UMA Graphics to include only the integrated adapter. Secondly, laptops can be variants of Integrated Graphics, Discrete Graphics. Individual hardware platforms display the name of the discrete card in the list of options. All models that allow this setting have a Switchable Graphics item to control switching by means of the operating system.

AMD switching

The set of drivers for AMD Radeon video cards also offers a utility that allows you to automatically switch to a discrete video card. To make the Appropriate settings, you need:

  • Launches Catalyst Control Center;
  • Go to the Nutrition section;
  • Select switchable graphics adapters.

All programs that have been launched since the drivers were installed are listed here. To configure the switching of a video card on a laptop, just select the High performance option for the desired program (a discrete card will be used). Where it is not necessary, it is worth setting the energy saving parameter (the integrated adapter is used).

Other useful settings can be made using the Catalyst Control Center, such as disabling the discrete graphics card. To do this, in the Power section, in the Switching method for graphic adapters block, it is enough to specify the integrated one for two power modes. In the same way, you can disable the built-in video card on a laptop, forcing all applications to use a discrete.

Switching using drivers works on older versions of the operating system, Windows 7, Windows 8, Windows 10. It also works on any laptop with such an OS, be it Lenovo, Asus, HP. Legacy system owners rather than software-switchable support will have to resort to more sophisticated methods.