How To Install An SSD In A Laptop

Disassembling a laptop

After we have prepared everything you need for replacement and purchased a suitable adapter for the SSD, you can start opening the laptop and then replacing the drive.

This can be done as follows:

Couldn’t fix the problem? Seek help from a specialist!

  • I turn off the laptop and wait until it turns off completely.
  • Turning over and removing the battery.
    How To Install An SSD In A Laptop

After the battery is disconnected, you need to remove the Installed hard drive.

For this:

  • Unscrew the screws and remove the cover on the other side of the battery.
  • In order to remove the cover, you need to pry it off and lift it.

The hard drive and memory modules are located under the cover. We need to remove the hard drive, since a solid-state drive will be installed in its place.

If you ask why exactly here we Install the SSD, and not instead of the drive, then there is a SIMple explanation for this.

When the speed of the bus to which the hard drive is connected is faster (in this case the hard drive is connected via SATA 3, while in the SATA 2 drive), then the SSD is installed in place of the HDD.

To properly remove the drive, you must strictly follow the following instructions:

Couldn’t fix the problem? Seek help from a specialist!

  • We unscrew the screws with which it is fixed.
  • Move the hard drive to the left and carefully remove it from the case.
  • Then we take out the hard drive from the mounting frame and put it aside. We will come back to it.
  • Install the SSD into the mounting frame.
  • After that we install our old hard drive into the adapter. It has a small instruction on how to properly secure the hard drive.

Putting both drives aside, we’ll come back to them later.

What you need to install?

First, you should familiarize yourself with the characteristics of your laptop to understand what components you need to purchase. As practice shows, in most modern models with a CD drive, you can easily install an additional hard disk. Therefore, problems should not arise.

Before starting, you should make sure that you have acquired everything you need to fully work.

You will need:

  • 2.5 “form factor SSD.
  • Tools for disassembling a laptop. Since all screw heads are the same, a small Phillips screwdriver is often required.
  • A plastic pick, a regular bank card, or any other SIMilar item for opening the case. The main thing is that it has no sharp corners, so as not to damage the train.
  • (adapter, slide) for replacing a 2.5 “drive.

Special attention should be paid to the last point, so let’s look at it in more detail.

Couldn’t fix the problem? Seek help from a specialist!

The topic is completely sorted out in this

Instructions for installing an SSD in a laptop instead of a floppy drive

Every user would like to install a modern SSD drive on their PC for better productivity and faster system performance. It is incredibly easy to install a solid state drive on your computer, and the process itself usually does NOT come with any difficulties.

By the way, there was a SIMilar article earlier, but in it we installed an SSD instead of a regular hard drive, for this we just had to remove a small cover on the back of the case, which does NOT create any difficulties.

But installing an SSD in a laptop instead of a DVD drive is much more difficult, because first you need to carefully disassemble it. And many users are already having difficulties at this stage. So let’s look at the whole process in more detail.

Software settings

The next step will be setting up BIOS, namely enabling AHCI mode. This mode allows you to increase the speed of the drive, mainly due to the advantages of the NCQ technology. Other options are also open, such as hot swapping.

  • We enter BIOS. Instructions.
  • Go to the “Main” section and set “AHCI” in the “Configure SATA as” option. The section names may differ in different BIOS versions, so try to look for SIMilar settings.
  • Save the settings “F10” and restart the PC.

Now you know how to put an SSD in a laptop instead of an old DVD drive, and you can do it yourself without any problems, just following our instructions.

By the way, you can completely transfer the system without losing its performance using Special programs, for example, such as Acronis Universal Restore, Macrium Reflect and others. They have wide functionality and will help you in this situation.

DVD drive

Now unscrew the DVD drive. We need a short screwdriver to remove the screw that secures the drive to the case. After unscrewing it, you can remove the drive without any problems.

Then remove the plastic cover from the DVD drive. To do this, you need to open it. This will require a paper clip or needle. We find a small hole on the front panel of the device and insert a paper clip there. After a slight push, the drive carriage will slide out of the case, and you will get full access to its bottom and can easily separate the plug from the carriage.

Once the plug is removed, it will need to be placed on the adapter.

Next, we remove the bracket that attaches it to the laptop from the drive, and rearrange it on our adapter in the same place.

After that, install the adapter in place of the previously extracted drive and tighten the fastening screw.

It remains to turn the laptop upside down and install the SSD disk in place of the old HDD. We close the cover removed at the beginning of disassembly and tighten the remaining bolts around the perimeter of the device, insert the battery.

The laptop is now assembled and ready to go. We installed two hard drives: we put the old HDD into an adapter and connected it instead of a floppy drive, and a new solid-state drive was mounted in its place.

How to choose an adapter?

The size of the drive can be of two types and differ in its thickness. 9.5mm and 12.7mm. Before purchasing an adapter, carefully measure the thickness of your drive and only then buy the Corresponding adapter. Otherwise, the SSD drive adapter SIMply won’t fit into the laptop instead of the DVD drive.

You should also pay attention to the interface through which the drive is connected. If the interface is SATA, then Using an adapter with an adapter to mSATA, you can easily put an SSD instead of a floppy drive. But if your DVD drive is connected via IDE, and this is an outdated technology, then to connect the SSD you will need an IDE to SATA adapter.

As mentioned above, adapters differ only in thickness, while their shape and width are the same. The adapter usually comes with a disposable screwdriver, screws for securing the hard drive and a plastic cover. The latter is needed for installation on an adapter to close the free space that is formed after removing the drive.

Removing the top cover

Now we need to remove the top cover of the laptop by unscrewing all the fixing screws. You should take into account the fact that they come in different sizes and you definitely need to remember where they were unscrewed from.

After all the screws are unscrewed, it is up to the pick. Now you need to separate the bottom and top of the laptop. You need to be extremely careful when opening it, since most models have NOT reliable latches, which can easily break. Check again if all the screws have been loosened, otherwise there is a risk of damage to the device case.

To remove the cover, you need to insert the pick into the gap between the top and bottom covers, and slowly turn it to unlock the latches inside the case. Start at the front of the laptop where the indicator lights are located. It is necessary to walk the pick along the perimeter of the entire body.

After separating the top cover from the bottom cover, DO NOT lift it up suddenly. Both parts are connected by loops and you could damage them.

When working with some devices, you do not have to disconnect the cables, since sometimes you can replace the DVD drive without removing the upper part of the device, which can significantly save your time.

Professional help

If it was not possible to fix the problem yourself,
then most likely the problem lies in a more technical level.
It can be: breakdown of the motherboard, power supply,
hard disk, card, RAM, etc.

It is important to diagnose and fix the breakdown in time.,
to prevent the failure of the second components.

How to install an SSD in a laptop?

First of all, the user should create a backup copy of the information that is stored in the laptop. Then. disconnect all wires from the laptop (mouse, headphones and charging), remove the battery by pulling the latches.

To put the drive into a laptop, the user should arm himself with a thin screwdriver and Unscrew the screws that are located on the back cover of the device. They cover the lid that protects the hard drive and laptop RAM.

READ  How to Choose an SSD for a Laptop

Life hack: using a plastic card (credit card, discount card), it is convenient to pry off the cover that covers the RAM and HDD.

3 ways to install:

  • In place of the HDD;
  • Instead of an optical drive;
  • The “tricky” method is to put a solid-state drive instead of a hard one, and install a hard drive in its place. It is suitable if the speed of the bus to which the old hard drive is connected is faster than that of the drive.

Interesting: if there is no free space for a second data carrier, but you want to leave a hard one, the owner of a laptop has the opportunity to purchase a case for a hard drive to connect an SSD via usb. True, this is convenient only if the laptop is used as a desktop device.

We put an SSD instead of a floppy drive

Preparatory actions Almost do not differ from those described above. So, the user needs to disconnect the laptop from the network and remove the battery. Then, using a screwdriver, Unscrew the screw that holds the cover covering the optical drive compartment.

There is a bolt under this cover that holds the drive. You will need to unscrew it, press the pedal: the drive will slide out of the connector. Now the drive is easy to get.

Important: to install an SSD instead of an optical drive, you need a adapter, which is the same size.

To securely fix the SSD disk, you need to screw four bolts into the disk until it stops, put it in the adapter and place it in the SATA socket. A rubber seal will add points to the reliability of fixation.

To prevent the SSD from dangling inside, the “” should be fixed in the case. To do this, you need to twist the drive mount and put it into the adapter. The shape of the fasteners is different, but the holes are located according to the standard, so the installation does not have to cause difficulties.

Life hack: so that the connector with the installed SSD (for example, Transcend 370 128GB) does not look handicraft, you can remove the cover equipped with a button from the optical drive. It keeps on latches, which are easy to unfasten with a credit card or pry off with nails. It remains to attach the cover to the adapter and fix it to the body with screws.

How to connect an SSD to a desktop computer?

Connecting the SSD to a desktop computer is not difficult at all. To do this, the user will need to de-energize the system unit, and also disassemble it. To get access to PC components and put in free space or replace the hard drive, you will need to remove the system unit panel.

In some cases the user will need to parse the entire block. Usually it is required by small-sized models (for example, DELL OptiPlex 3040 SFF).

Life hack: there is a button on the back of the system unit that serves to turn off. You will need to hold it for a few seconds. Do this before disassembling the system unit. In this case, the PC will NOT start, since the device is disconnected from the network, but such manipulation will remove static electricity from the motherboard, as well as other internal components of the computer.

The SSD drive is installed in the free space using a special adapter, made in the form of a slide and attached with screws. Fasteners are supplied with the drive in the kit. An adapter is required because the form factor of the carrier can be smaller than the dimensions of the slot. For example, the classic tray is designed for 3.5 “part, and the most common size of solid state devices is 2.5”. as in SAMSUNG 2.5 “750 EVO 120GB.

When the disk is delivered, you need to connect the SSD using a SATA cable to the “motherboard” by selecting the appropriate slot on it. Then the SSD should be connected to the power supply, which ensures the well-coordinated operation of all computer components.

Important: The drive is fastest only when connected to a SATA 3.0 slot with at least 6 Gb / s speeds. Usually this connector is marked and painted black, so it is not difficult to see it on the board. However, if there are designations, you should find the documents on the motherboard and find information in them in SATA.

When the disk is delivered and the system unit is assembled, the SSD needs to be configured for normal operation of the media. To do this, you need to go into the BIOS, find a solid-state drive there and, if this drive acts in addition to a hard drive, put the SSD first in the list. Thus, the SSD will become the main.

As soon as the Installed SSD became the first in the BIOS, you should confirm the changes, and then reinstall the operating system. You can SIMply copy the OS to the media if there is an HDD or users do NOT plan to leave the SSD as a system disk.

Attention! If the drive will work as a system disk, you should use the classic preinstalled Windows tools for configuration (usually the system itself optimizes work, which extends the life of the media). When the operating system remains on the HDD, the same disk must be marked in the BIOS as the main one.

The classic method. replacing the HDD

So, the battery is removed, the cover is unscrewed. The time has come to pull out the hard disk: the disk is fastened with a few bolts, they must be unscrewed, and then carefully remove the hard drive from the SATA slot. In this place you will need to install a solid state drive and secure the SSD with screws. Final installation steps: attach the cover, place the battery, and turn on the laptop.

During bootup of a laptop (eg HP 250 G5), the user will need to enter the BIOS. There he will see that the system has detected the SSD. Now you need to check in which mode the disk is operating in the tab called Advanced: if not in AHCI, it will switch the media to this mode and save.

The last step is to install the operating system.

Difficulties to Face

When installing an SSD or starting a computer / laptop after an upgrade, the user may encounter some difficulties. Most of them are solved at the initial stage.

So, the first thing you should pay attention to when installing an SSD drive yourself (for example, Kingston HyperX Fury 120GB) into a computer or laptop is accuracy. Most housings are made of plastic, so careless actions can damage the skin. For example, the weak point of laptops is the jacks for wires.

Attention! It is better to supplement both a portable and a desktop device with an SSD when the computer warranty is over: any upgrade made by the user can “destroy” the warranty.

If you plan to install the SSD media in the optical drive slot, you must take into account the thickness of the adapter. Most models are available in 12.7 millimeters or 9.5 millimeters. To be sure that the adapter will fit, you need to find out the model of the drive and find its characteristics on the Internet.

A solid-state hard drive (for example, SANDISK 2.5 “SATA 3.0 Plus 120GB) is installed, but the device” does not see it “? You will need to look into the BIOS again and in the SATA Mode or Advanced item, double-check whether the system is functioning in AHCI. a mode designed to work with SSD.

Please note: in IDE mode, the system recognizes the SSD disk, but some functions that increase the speed of work and increase the “life years” of the hard drive do not work. Therefore, it is worth checking the current mode through the dispatcher. If IDE is set. you need to switch the system to AHCI.

BIOS does NOT display SSD: 3 reasons

  • Contact with SATA is “loose”: you need to open the cover and check if the drive is fully inserted into the slot.
  • The problem is in the SSD drive itself. it happens if you bought a used version, or the drive was “lying around” for a long time: it is checked on another PC.
  • Outdated BIOS: Search and update fix the problem.

The SSD is installed correctly, everything is displayed, but the computer is still weaving like a turtle and “creaking” when opening Photoshop? The PC is too old. With a dual-core processor, but with 2GB of RAM and a “motherboard” that was released more than three years ago, there is nothing to hope for. Also, performance will NOT increase if the drive is connected to SATA older than the third version.

How to properly install an SSD on a computer and laptop? 3 ways

To improve the performance of your computer, as well as to get rid of the noise during the operation of a laptop or system unit, an SSD drive is useful. a large, fast and silent “flash drive”.

Note. The computer will not “beep” if you install only the SSD. I installed such a device as an addition to the classic hard, the owner of the computer will NOT get rid of the noise, but will speed up the work of the “machine” and increase the storage.

In the article, we examined the options for connecting an SSD drive to a desktop PC, as well as installing it into a laptop. From the material you will learn what to do to put a solid-state drive and configure the system for the SSD yourself.

Cheat sheet: how to work with SSD for a long time

Solid-state drives “are not friendly” with high temperatures, so you should think about installing an additional cooler in your desktop computer and working with a laptop on a cooling pad.

READ  How To Transfer Photos From Phone To Laptop

SSD manufacturers release firmware updates for devices, which improve performance and extend the life of the drive.

Also, the developers recommend not transferring from a hard one, but installing a new Windows on a solid-state hard drive: versions from seven and “younger” optimize its work automatically.

The article discusses comfortable ways to connect a solid-state drive to a computer and laptop. Such an upgrade will speed up the operation of the device and also reduce noise. The main thing is to do everything neatly and prepare the tools in advance. Please be aware that slot locations and fasteners may vary from device to device.

See the detailed instructions on how to put the SSD into a laptop.

What is needed for work?

Installing an SSD in a laptop is a SIMple task and does not take much time. But when upgrading, it should be borne in mind that self-replacement of components may violate the terms of the warranty. However, if the warranty period for the laptop has already expired, you can take a chance.

What you need to install an SSD disk:

  • Solid state drive, which is connected using the SATA interface, and a laptop.
  • Screwdriver. Depending on the fastening of the laptop cover, you may need a cross or straight.
  • Something thin to pry off the lid. A special spatula for laptop repairs or a regular plastic card will do.
  • Second data store. If the SSD is NOT delivered, but replace the hard drive with it, then you will need an additional drive to transfer files.

Interesting: some manufacturers equip notebooks with two types of media. So in the top-end gaming Predator Helios 500 PH517-61 there is a two-terabyte hard drive and a 512 gigabyte SSD in addition.

SSD storage options

There are four methods for installing a solid-state device in a laptop:

1. The easiest way is to remove the hard drive and connect the solid drive instead. It is important to take care in advance to transfer all the files that are stored on the HDD to another medium.

Tip: If you need a solid body for gaming, a volumetric model that can withstand heavy loads is suitable. Two terabyte 860 QVO. just like that.

2.Place the SSD in place of the classic hard drive, but convert the hard drive to external storage using a USB box.

3. Replace the SSD optical drive. An adapter box is needed here. The user needs to insert the SSD there, remove the OP, and then place the box with the SSD in its place. The method is not suitable for those who use an optical drive and those who do not have one.

Note: when buying such a box, consider its thickness. It must match the parameters of the OP. You can see how thick the drive is installed by removing it and measuring it with a centimeter. Another option is to enter the exact name of the drive in the search engine to see its parameters.

4. Put the solid-state device in place of the hard drive, and the screw is already installed instead of the OP using the box, which was described in the previous method.

Recommendation: If you need an SSD as a system drive, a large capacity is not a prerequisite. Models up to 256 gigabytes are also enough, for example, A400 240GB.

How to install an SSD in a laptop. a detailed guide in 3 sections

To speed up the laptop, sometimes it is enough to insert the SSD drive. This task is SIMple, you can do everything yourself. The instruction will tell you how to proceed. The manual contains both a preparatory stage and, in fact, a description of the installation process.

How to install SSD instead of HDD

This is the easiest way. How to proceed is described in the table.

Interesting: the M.2 format models look like a stick of RAM. These SSDs are often installed in light and thin portable computers.

Recommendation: if you need an inexpensive but reliable SSD option, you can choose a model with MLC memory, for example, SSD370S.

Now you can start checking the newly installed components in the BIOS.

You need to see if the laptop sees the SSD. If the carrier is NOT detected, it may be due to:

  • Poor interface contact: maybe the solid-state device is not fully inserted into the connector;
  • The drive itself is faulty: you can check this with a second computer;
  • BIOS is outdated, in which case it will need to be updated.

Curious: the powerful ThinkPad E570 laptop already has an SSD, but if you want to put a second one, you can replace it with the drive.

If everything is in order, the laptop recognizes the drive, then you can start checking the mode of operation of the solid-state drive. Need AHCI: This is a special mode for working with solid state drives. It allows you to activate all the advantages of SATA connection, in particular High speed. You can see the mode in the Advanced section of the BIOS. If it is shown that the SSD is operating in a different mode, it needs to be switched and all parameters saved.

Tip: If you want a high-speed, super-capacious model, the 970 PRO will do the trick. It works on a modern type of memory and has an impressive size.

Now you can install the operating system. Experts recommend installing the OS again so that it automatically configures its services to work with solid-state storage.

As you can see from this guide, you can put an SSD into a laptop in several ways. If you put it in place of the hard drive, adapters are NOT needed. However, if you want to leave the HDD, there is still a solution. The connection process itself is SIMple, but you need to remember: if you disassemble the device, then you will NOT have to rely on warranty repairs.

How to install SSD on laptop and PC? Several reliable ways

Installing solid-state drives by default on laptops and computers has recently begun, and the device purchased only 1-2 years ago most likely comes with a regular SATA HDD.

This option is also not bad. especially if the SATA III interface is used, however, ordinary hard drives are unable to provide maximum performance.

HDD installation

It is advisable to install the hard drive back in cases where the system remains on it.

Or, if the size of the SSD is not enough to accommodate all the necessary information there, and the solid-state drive itself is used to store only system files and the operating system.

At the same time, the data transfer rate of the optical drive is quite sufficient to support the operation of the HDD.

And ensuring effective use of SSD in this way will NOT work.

Therefore, it is the standard hard drive of the laptop that is inserted into the adapter, and the floppy drive is removed. especially since today it is practically not used.

The adapter for HDD connection is selected according to the thickness of the drive, which can be equal to either 12.7 or 9.5 mm. Further, in turn, the following actions are performed:

  • The drive is installed inside the adapter;
  • The optical drive is removed from the laptop (in most models it is held by one screw). To do this, you need to open the discs (usually it is enough to press a button with a thin needle inside a special hole on the panel in front of the button;
  • The panel is removed from the drive tray and installed on the adapter so that the replacement does not affect the appearance of the device;
  • The hard drive in the adapter is put in place of the drive;
  • The screw is tightened, which is now attached to the HDD.

Caching

You can enable caching to make the disk faster. You can process files by typing devmgmt.Msc on the Run menu.

This will open the Device Manager, where you can open the properties of the desired drive and enable file caching in the policy tab.

Disable indexing

To disable indexing, you should:

  • Open the “My Computer” window;
  • Name the disk with the right mouse button and select “Properties”;
  • Uncheck file content indexing.

System Setup

After returning the hard drive and installing the solid state, the system should automatically detect the type of the new device and install all the software necessary for it.

Another utility like Migrate OS to SSD may be needed if you need to move the operating system to a new one from the old disk.

Now you can proceed to the basic steps to optimize the system. These include:

  • Enabling the TRIM function;
  • Turn off automatic disk defragmentation;
  • Prevent indexing of files and enable their caching.

The TRIM function, which is necessary in order to timely detect the space left after deleting files, is included in Windows, starting with the 7th version.

If disabled, disk performance degrades over time.

To test the function, open the command line as administrator and enter the command fsutil behavior query disabledeletenotify.

If the result is 1, then TRIM is not working. You can enable it by calling the date again and entering fsutil behavior query | set DisableDeleteNotify = 0.

What you need to install an SSD drive

A user who wants to speed up access to information will need:

    • Purchase an SSD with a suitable volume and price (a 60-128 GB device is enough to work with documents and basic programs, for more resource-intensive tasks you should think about buying a 500-1000 GB device)
    • Enable AHCI mode for working with high-speed drives (if it was NOT done before)

    For more information on how to do this, read the article “I can not install windows 7: how to solve basic errors”

    • Disassemble the computer and install the solid state drive. In this case, the PC may need to remove the old HDD (for further installation using an adapter and a CD-ROM drive). Desktop PCs usually have enough space for an SSD.

    As a result, the user gets:

    • Increasing the speed of working with data;
    • Reduced power consumption and weight (important for laptops)
    • No need to defragment the disk.
    READ  How To Make The Keyboard Luminous On A Lenovo Laptop

    Installing an SSD on a computer

    Standard SSD size is 2.5 ”.

    3.5-inch versions were also produced, however, due to the fact that they were most often installed on laptops, only the smallest drives remained (including 1.8-inch and M2 formats).

    This means that for installation on a PC, an SSD requires the use of so-called sleds, or rails. devices for securing the disk inside the bays designed for standard HDD and drives.

    And, although, due to the light weight of the solid-state drive, it weighs a little and can only be mounted on one side of the case of the system unit, you should not do this. it is safer to purchase a small adapter from 3.5 to 2.5 inches.

    Disk installation is carried out in several stages:

    • The computer is de-energized;
    • The power supply is turned off using a button on the back of the system unit;
    • The power button is pressed and held for a few seconds. In this case, a de-energized computer, of course, will not start, however, static electricity will be removed from the motherboard and other parts;
    • The PC case is disassembled (usually only one panel is removed for this, most often the left one, but sometimes you have to disassemble the system unit almost completely;
    • The SSD is installed in place (for a PC, it is not necessary to remove the HHD that was already there) using an adapter slide and secured with screws. The hardware is included with the device;
    • The installed disk is connected to the motherboard via a SATA cable and the corresponding slot on the “motherboard”;
    • The disk and the computer’s power supply are connected;
    • Assemble the system unit and configure the SSD.

    As a rule, the maximum speed of the drive will be ensured only when it is connected to a SATA 3.0 or higher connector at speeds up to 6 GB / s.

    On the board, it usually differs from others in black color and markings. In the absence of any designations for SATA 3.0, you should read the documentation for the “motherboard”.

    It is worth noting that SSD drives do not tolerate high temperatures well.

    Therefore, when adding a new drive, it is worth taking care of improving the cooling system.

    To do this, you can provide, for example, an additional 80 × 80 or 120 × 120 cooler in the side of the system unit.

    Such a fan will perfectly cool not only a solid-state, but also a regular drive.

    Work setup

    After installing the disk, first of all, you need to configure the media for its optimal performance and increase its service life:

    • Go to BIOS (or UEFI) using one of the methods available in your operating system. The easiest way to do this is for Windows 7, I pressed the function key during reboot (different letters are used in different manufacturers of the motherboard or laptop)

    For more information on setting up a boot disk, read our material: How to reset Windows 7 password. Instructions.

    • Put the SSD drive first in the list of devices (if It is not the only drive)
    • Save changes and restart your computer.

    Now you can either transfer the system to a solid state drive in order not to reinstall.

    Or leave the old OS if the SSD will not be used as a system disk.

    When choosing the first option, you should use either the built-in Windows tools (they are available in systems starting from version 7 and higher), or applications such as Acronis True Image.

    In the second case, when the system remains on the HDD, the same hard disk should be left first in the boot list in the BIOS.

    Installation on a laptop

    Installing solid state drives on a laptop is slightly different.

    First of all, due to the fact that there is less space inside the case of a laptop and, most likely, to connect a second disk, the user will have to remove the first.

    But after installation, the laptop will work faster, and the battery life will practically NOT decrease, even if you reconnect the old HDD.

    For installation, the user will need a standard SSD and a floppy adapter. The main installation steps include:

    • Power off the laptop (by removing the battery)
    • Opening the back cover and carefully removing the HDD. This turns off the loop and the power wire;
    • Replacing the SSD hard drive with a ribbon cable;
    • HDD installation using an adapter;
    • Replacing the laptop cover;
    • Turning on the laptop and setting up the system.

    Connecting an SSD to a desktop computer

    To begin with, if you have already disconnected and connected a regular hard drive to your computer, then the procedure for a solid state drive looks almost exactly the same, except for the fact that the width of the device is NOT 3.5 inches, but 2.5.

    Well, now from the very beginning. To install the SSD on a computer, unplug it from the power supply (from the outlet), and also turn off the power supply (button on the back of the system unit). After that, press and hold the on / off button on the system unit for about 5 seconds (this will completely de-energize all circuits). In the guide below, I will assume that you are NOT going to disconnect old hard drives (and if you are, just Disconnect them in the second step).

    • Open the computer case: usually, it is enough to remove the left panel to gain the necessary access to all ports and install the SSD (but there are exceptions, for example, on “advanced” cases, the cable can be routed along the right wall).
    • Install the SSD into a 3.5 ” adapter and secure it with the bolts provided for this (this adapter is included with most solid state drives. In addition, your system unit may have a whole set of shelves suitable for installing both 3.5 and 2.5 devices, in this case you can use them).
    • Place the SSD in the adapter in the free space for 3.5 inch hard drives. If necessary, fix it with screws (sometimes latches are provided in the system unit for fixing).
    • Connect the SSD to the motherboard with an L-shaped SATA cable. Below I will tell you more about which SATA port the drive should be connected to.
    • Connect the power cable to the SSD.
    • Assemble the computer, turn on the power and immediately after turning on go to the BIOS.

    After entering BIOS, first of all, set the AHCI mode for the solid state drive to work. Further actions will depend on what exactly you plan to do:

    • If you want to install Windows (or another OS) on an SSD, while you, in addition to it, have other connected hard drives, install the SSD first in the list of drives, and put the boot from the disk or flash drive from which the installation will be performed.
    • If you plan to work in an OS that has already been installed on the HDD without transferring it to the SSD, make sure that the hard disk is the first in the boot queue.
    • If you are planning to transfer the OS to an SSD, you can read more about this in the article How to transfer Windows to SSD.
    • You may also find this article useful: How to Optimize an SSD in Windows (This will help improve performance and extend its lifespan).

    As for the question of which SATA port to connect the SSD to: on most motherboards you can connect to any one, but some have different SATA ports at the same time. for example, Intel 6 Gb / s and third-party 3 Gb / s, the same on AMD chipsets. In this case, look at the port signatures, motherboard documentation, and Use the fastest for SSDs (slow ones can be used, for example, for DVD-ROMs).

    How to install an SSD

    If you are thinking of upgrading your PC or laptop with a solid state drive SSD, congratulations, this is a great solution. And in this manual I will show you how to install an SSD on a computer or laptop and try to give other useful information that will come in handy with such an update.

    If you have NOT purchased such a disk yet, then I can say that today installing an SSD on a computer, while it is not very important whether it is fast or not, is what can give the maximum and obvious increase in the speed of its work, especially during all non-game applications (although it will be noticeable in games, at least in terms of level loading speed). It can also be useful: Setting up SSD for Windows 10 (suitable for Windows 8), Programs for SSD drives.

    How to install an SSD in a laptop

    To install an SSD in a laptop, first of all unplug it from the outlet and remove the battery if it is removable. After that, Unscrew the hard drive compartment cover (usually the largest, near the edge) and carefully remove the hard drive:

    • It is sometimes mounted on a kind of skid that attaches to the cover you just unscrewed. Also try to find instructions on how to remove the hard drive directly from your laptop model, it may be useful.
    • You need to take it out not in yourself, up, but first sideways. so that it disconnects from the SATA contacts and laptop power.

    In the next step, Unscrew the hard drive from the carrier (if required by the design) and install the SSD in them, then repeat the steps above in reverse order to install the SSD in the laptop. After that, on a laptop, you need to boot from a boot disk or flash drive in order to install Windows or another OS.

    Note: you can also use a desktop PC to clone an old laptop hard drive to an SSD, and only then install it. in this case, no system installation is required.