Failed to activate touch ID on iPhone

How to fix “Failed to activate Touch ID on this iPhone” problem

To get rid of the unsuccessful activation of Touch ID, I recommend doing the following:

    Install update 10.3.3 for your iOS. For some users, the problem was solved in a similar way;

failed, activate, touch, iphone

Install update 10.3.3 for your iOS

  • Make sure you have the latest version of iOS installed;
  • Also make sure your fingers, as well as the Home button, are dry and clean. If necessary, use a clean, soft cloth to clean the surface of the Home button from dirt, moisture, etc.;
  • Your finger should be in full contact with the surface of the Home button, touching the metal ring surrounding the button. When scanning your finger with Touch ID, you must not press too quickly, or move your finger around the button;
  • If you use special tools to protect the screen, make sure that they do not cover the surface of the Home button, or the ring surrounding this button;
  • Go to “Settings”, select “Touch ID and Passcode” there, and make sure that the phone unlocker or “iTunes App Store” is turned on (value “on”), and that the phone already has fingerprints of one or more of your fingers;
  • Go to “Touch ID & Passcode” to test the iTunes App Store

  • Try adding another fingerprint to your phone;
  • Use a forced restart of the phone. Hold down the Home and Wake / Sleep buttons for 15-20 seconds until the Apple logo appears;
  • Try resetting your iPhone to factory defaults. To do this, go to “Settings”, then to “General”, then to “Reset”. “Reset all settings”;
  • If possible, roll back the system to the previous (before update 10) state (some users were helped by a rollback to update 9.3.5);
  • For some users, reconnecting the Touch ID loop helped solve this problem. To do this, you need to disassemble the iPhone, disconnect the “Home” button cable, and then reconnect it. It is recommended to perform this operation if you have sufficient qualifications, otherwise you risk putting the phone out of order;
  • If you are unable to add more than one of your fingerprints to the phone database, contact the Apple Retail Store or Apple Authorized Service Provider with this problem, also try to write to Apple support;
  • Visit the nearest service center to see if they can help fix the problem with activating Touch ID.
  • Experts note that a software solution to the problem with Touch

    After performing a system update of iOS (usually updates to versions 10 / 10.1 / 10.2 / 10.3.2), the user’s iPhone may start displaying the message “Failed to activate Touch ID on this iPhone” upon reboot. Access to the user’s Touch ID is blocked, and various “dances with a tambourine” aimed at correcting the situation are usually ineffective. In this article I will tell you what this error “Failed to activate Touch ID on this iPhone” on 5s and 6 is, and how you can fix it.

    Error text “Failed to activate Touch ID on this iPhone”

    Re-creating Touch fingerprints This method works most often if the TouchID stopped working after updating iOS and does not work in any application.

    The steps to fix the problem will be as follows:

    • Go to Settings. Touch After that, everything should work, and the error with the message that you cannot complete the Touch ID setup should not appear again.

    A Few Tips

    In order to eliminate the consequences of an unsuccessful activation of the Touch ID service, there are some tips to keep in mind:

    • Install update 10.3.3 for your Apple gadget. A number of users have solved the problem with Touch ID this way.
    • Make sure your fingerprint as well as the Home button are clean and dry. If necessary, wipe both the button and the fingerprint of a soft cloth thoroughly. It is important to remove any dirt, moisture and grease stains, as they will “smudge” and blur the print when using Touch ID.
    • You also need to make sure that the fingerprint fits as tightly as possible to the Home button and to the ring that surrounds this button.
    • Pressing the Home button is necessary not too quickly, and during authorization in this way you cannot move your finger.
    • It is also important to make sure that the protective and additional tools do not touch or cover the button with the Touch ID sensor (this is in the event that the user uses any additional tools to protect the display, such as a protective screen or case).
    • You can also go to Settings and select Touch ID and Passcode there. ” It is important here to make sure that the gadget unlocker and the iTunes App Store are running (that is, they are set to on).
    • Another point to be sure is that the database of your personal gadget contains prints of one or, even better, several fingers.
    • You can use a forced restart. To do this, hold down the Home button and the Wake / Sleep button at the same time for 20 seconds or until the Apple logo appears on the display.
    • In which cases, the problem with Touch ID can be solved by resetting all gadget settings to their factory values. In order to do this, you need to go to the settings, find the basic settings there and select the reset section.

    Do not forget about another way to solve the problem, only more radical and requiring the qualified help of an experienced specialist. It’s about reconnecting the Touch ID loop. In order to do this, you must first disassemble the phone, and then disconnect the Home button loop from the general device and connect this loop back. And, as mentioned above, it is better to make sure that this procedure is performed by qualified and experienced specialists.

    How to fix the problem. classic calibration scheme

    Today, the easiest way to solve the problem with Touch ID is to recreate the fingerprint. Apple has done a lot of work in this area over the past few years, including also focusing on fixing bugs with Touch ID.

    This can be helpful if your fingerprints have changed slightly over the past months or years due to wear and tear, dry skin, or other reasons. For calibration, it is worth doing the following percentages:

    • Launch the “Settings” application and go to the “Touch ID and Passcode” section.
    • Enter your password when prompted to do so.
    • Select the fingerprint with which there were login problems.
    • Click on “delete fingerprint”.
    • Click on “Add fingerprint” and re-scan.
    • Place your finger on the Touch ID sensor in different ways. from the sides, from top to bottom, and from right to left. This should be done until the fingerprint is completely colored.
    • After the phone asks you to set up the grip, you should scan the edges of your finger. This must be done until the print is completely colored.
    • Click on “Continue” and wait until the process is complete.

    Note: it is worth putting your finger on the way it will lie on the sensor with a comfortable grip of the device.

    What causes the error

    Do not worry too much about your phone, since this problem is international in nature. users all over the world face it in one way or another. As noted by Apple employees and others, this problem is hardware, not software. For this reason, most often it will be impossible to solve it using applications or programs.

    iPhone 6 Failed to Activate Touch ID

    One of the problems that iPhone and iPad owners face when using or setting up Touch ID is the message “Failed. I can’t complete the Touch ID setup. Come back and try again ”or“ Failed. Unable to complete Touch ID setup “.

    Usually, the problem disappears by itself, after the next iOS update, but as a rule, no one wants to wait, and therefore we will figure out what to do if we cannot complete the Touch ID setup on the iPhone or iPad and how to fix the problem.

    Other ways to fix the “Can’t complete touch setup” error

    If the method described above did not help you, then it remains to try other options, which, however, are usually less effective:

      Try to delete all fingerprints in the Touch settings And, finally, if none of this helps, then you should either wait for the next iOS update, or, if the iPhone is still under warranty, contact an official Apple service.

    After some system updates for iOS, the iPhone may display a notification like “Failed to activate Touch ID” during reboot. As a result, access to the Touch ID system for the user is blocked, which can lead to more serious failures. How to solve the error?

    Touch ID doesn’t work at all

    Of course, the likelihood that the fingerprint scanner is out of order also exists. Although users complain about such breakdowns relatively rarely. If, after updating the fingerprint, Touch ID did not work properly, then you can try “hard reset” by creating a backup. If the problem is programmatic, then a hard reboot should fix it. Otherwise, you will have to visit the service center, since it is unlikely that you can do without qualified diagnostics.

    If Touch ID Doesn’t Work on iPhone or iPad: How to Deal with the Problem

    Touch ID is the official name for the fingerprint reader found on the iPhone 5s, iPhone 6 and iPhone 6 Plus smartphones, as well as the iPad mini 3, iPad mini 4, iPad Air 2 and iPad Pro tablets. Apple claims that the newer version of Touch ID is installed in the iPhone 6s and iPhone 6s Plus models, and on the forums, users claim that Touch ID often does not work, both the “old” and the new.

    Touch ID is, of course, a useful solution, moreover, not only from a marketing point of view, but also from a purely practical one.

    Users can use it to unlock their iPhones and iPads, log into accounts in various online services, and even pay for purchases using Apple Pay.

    But only if Touch ID works fine. But, unfortunately, like any other electronics, this one is also sometimes capricious. Therefore, let’s figure it out.

    To begin with, we note that if problems with Touch ID on your Apple device began after a recent update of its operating system to iOS 9 and / or even newer versions of it, then, most likely, a downgrade may be needed (i.e., a rollback of the system to the previous version), or, if the problems are not so critical, then it is better to wait for the next update.

    With other problems of the fingerprint scanner in iPhones from 5s and newer, as well as in iPad mini 3, mini 4, Pro and Air 2, you can try to figure it out, so to speak, on your own and even at home. Fortunately, there are not many such problems, and the ways to eliminate them are already known. So if:

    Touch ID does not work in the App Store

    This is also a notable problem. Most often, the reason that the scanner stops working with the App Store is also a cosmetic factor, but often the problem occurs due to software malfunctions. Some users complain that since iOS 8.3, Touch ID is simply not displayed in the App Store.

    In such and similar cases, we do the following:

    • click “Settings”. “Touch ID and Password”;
    • in the “Using Touch ID” section, disable “App Store, iTunes Store”;
    • restart the iPhone (or iPad);
    • we return to “Settings” again. “Touch ID and Password” and turn on “App Store, iTunes Store”.

    After that, the Touch ID bug in the App Store should resolve itself. We also remind you that if you haven’t made any purchases in the App Store within 24 hours, the system will ask for a password at the entrance.

    Touch ID does not work in winter or in cold weather

    Statistics show that in low temperatures, the fingerprint scanner in the iPhone and iPad is more likely to fail. The problem, again, in most cases has a simple explanation. The fact is that in cold weather the papillary pattern of the fingers changes. It is difficult to notice these changes with the naked eye, but Touch ID notices them and starts to malfunction. As you probably already guessed, a nuisance is also treated by updating the fingerprint. But you can do even easier and enter a special “winter” print into the device’s memory. scan your finger pattern immediately from the cold. True, they say that both methods only partially solve the problem, but it’s still worth trying.

    Touch ID not working. crash

    READ  How to clean iPhone through computer

    If Touch ID fails, then a simple reconfiguration is recommended to deal with this nuisance. In other words, you need to retrain your iPhone (or iPad) to recognize your fingerprint. Since the appearance of scanners, Apple has regularly updated their software so that smartphones and tablets of users remember the “fingers” of their owners longer and better.

    It seems like a radical optimization was carried out back in iOS 8, but, as practice shows, if you do not refresh the print, then over time (from a month or longer), Touch ID will fail anyway, but it happens. The reasons can be very different, but, as a rule, they are purely cosmetic in nature: slight “wear” of the print itself, dry skin of the finger, etc.

    Therefore, if Touch ID suddenly malfunctioned, then first update the fingerprint in the memory of your smartphone or tablet. But first, you should carefully wipe the surface of the scanner and wash your hands. Next, go to “Settings”, then. to “Touch ID and Password”. We delete old prints by swiping across the screen from right to left. After that, we tap “Add a fingerprint” and re-carry out the standard procedure for entering a fingerprint according to the instructions.

    Touch ID does not work when dirty or wet

    Well, there’s really nothing to explain here. It is clear that moisture or dirt (whether it is on the skin of the finger or on the surface of the scanner) is very effective in preventing any fingerprint from being scanned. Therefore, if the scanner has excess wet and / or dirty substances on it, it is better to wipe it with a dry, clean cloth. And you need to wash your finger (you can even wash it with your hands). However, you should not overdo it with water, because if you keep your hands in water for a long time, the fingertips will wrinkle and the papillary pattern will change for a while. Apple claims that in the new iPhone 6s and iPhone 6s Plus, Touch ID works better with wet skin, but still the manufacturer does not recommend using the scanner with wet hands.

    Remove iPhone Passcode to Fix Touch ID Not Working

    The easiest way. remove Touch ID when your iPhone is locked due to Touch ID not working. To remove Touch ID from iPhone, you need Apeaksoft iOS Unlocker.

    Unlock Apeaksoft iOS is an iPhone unlocking software to solve various iOS system problems. When Tough ID is down and iPhone is locked, you can use this Touch ID lock removal software, sue your iPhone and create a new Touch ID or password.

    Download iOS Unlocker for free on your computer by clicking on the download link below. Run this program after successful installation.

    In the main interface, select Wipe Password Mode. Get a USB cable to connect your iPhone to your computer. Click on the Run button.

    Step 2. Confirm iPhone information

    Then this program will show information about your iPhone such as type, model, etc. Launch Click the button to continue if all information is correct. Otherwise, you must correct the information first.

    Then, this tool will download iOS firmware from Apple server based on your iPhone information. Do not disconnect your internet connection at this point.

    Step 4. Unlock iPhone Touch ID

    After the firmware download is complete, click the Unlock button and enter 0000. Then click the Unlock button again and this program will remove Touch-ID lock from iPhone.

    General solutions to fix Touch ID not working

    Follow these steps to find out what is causing your Touch ID to malfunction and how to fix it. These are common solutions with which you can easily fix the Touch ID error and get back to normal.

    disable iTunes Store and APP Store

    Some Apple users are complaining that they cannot make a purchase from the iTunes Store or App Store after the iOS 11.2 / 11.1 / 11 update. Additionally, some users have reported that Touch ID no longer appears on older versions of iOS. To fix Touch ID failed iOS 11 error, you can sign out of iTunes Store and App Store and then reopen it to fix.

    Open the Settings app on your iPhone. Scroll down to select the Touch ID & Password option. Then you will need to enter his password.

    Disable both iPhone Unlock and App & iTunes Stores. At this time, press the Home button to immediately return to the Home screen, and then restart your iOS device by pressing the Home button and the Power button at the same time. For iPhone 7/7 Plus / 8/8 Plus / X users, there is something more than restarting iPhone.

    Step 3. Add a new fingerprint to your iPhone

    Go back to iPhone settings. Click Touch ID & Password and then enter your password again. Set the following Unlock iPhone and App & iTunes Stores options to green. Click Add Fingerprint to add another fingerprint. As a result, the next time you fail to complete the Touch ID setup, go back and try again.

    delete and re-add your Touch ID fingerprints on iPhone / iPad

    When you constantly have a problem with your fingerprint, it is better to delete the old one and install a new one. If you are unable to activate Touch ID on iPhone 6 Plus and iOS, follow these steps.

    Step 1. Delete Touch ID Fingerprints on iPhone / iPad

    Scroll down and select “Touch ID & Passcode” in iPhone Settings. Enter your password when prompted. Then select any fingerprint you added earlier and click the Remove Fingerprint button. Repeat the above operations until you have deleted all previous fingerprints on iPhone.

    Step 2. Reset and re-add Touch ID

    Find and tap the Add Fingerprint button to set up a new fingerprint using the onscreen instructions. It will guide you through every step you need to take in detail. Additionally, if you have Touch ID issues on MacBook Pro, you can also delete and re-add Touch ID Fingerprints on Mac to fix.

    How to fix Touch ID error on iPhone and iPad after iOS update

    Many people report that Touch ID doesn’t work with other experiences. As mentioned above, someone is having a problem with iPhone 6 Touch ID failing after screen replacement, while others are unable to activate Touch ID for one reason or another. Luckily, this article can help you fix Touch ID issues with simple, detailed solutions.

    • General solutions to fix Touch ID not working
    • 2 Professional way to fix Touch ID error

    iPhone recovery using iTunes

    If you’ve backed up your iPhone with iTunes before, there is a new way to fix Touch ID not working issues. When restoring with iTunes, all your iOS data will be erased and replaced with the previous iTunes backup. This way, you can remove the factors that cause Touch ID to crash.

    Connect iPhone to computer with USB cable and launch latest iTunes.

    Step 2. Restore iPhone to Fix Touch ID Not Working

    Select the icon for your iPhone and find its Summary section. Click “Restore iPhone” and confirm to restore your iPhone.

    force restart your iPhone / iPad

    If you are unable to complete the Touch ID setup for iOS 11, or if you have other problems with Touch ID not working, Force Restart is a useful solution. It can fix many system crashes automatically.

    Force restart iPhone 6s and earlier and iPad:

    Step 1. Hold and press the Home button and the Power button

    Step 2. Continue to hold for about 10 seconds

    Step 2. Release the two buttons until you see the Apple logo

    Hard restart iPhone 7/7 Plus:

    Step 1. Hold and press the power button and volume down button at the same time

    Step 2. Don’t let go of them until the Apple logo appears

    Force restart your iPhone X / 8/8 Plus:

    Step 1. Quickly press the volume up button

    Step 2. Quickly press the volume down button

    Step 3. Hold and press the power button to restart iPhone

    Professional Way to Fix Touch ID Failed

    If the above methods don’t work or you can’t find the true cause of Touch ID crashing, you need iOS smart recovery software. Here are 2 recommended softwares.

    Disable Activation Lock in iCloud, unable to activate iPhone / iPad

    If you are unable to activate your iPhone or iPad, you can remove Activation Lock in iCloud. This way you can reactivate your iOS device as usual.

    Step 1 When you see iPhone / iPad failed to activate, you can first turn off your iOS device.

    Step 2 Open a browser on your computer and go to iCloud.com.Here you can sign in with your Apple ID.

    Step 3 When you enter the main interface, select Find my iPhone / iPad feature. Then confirm your Apple ID password and select All Devices. At this point, you can check the specific iPhone or iPad that cannot be activated. Then select to remove it from your account.

    Step 4 After all these operations, you can turn on the iPhone or iPad and then activate it again.

    restart or fix failed to activate iPhone iPad

    Sometimes, iPhone iPad activation issue cannot be caused by app crashing, bugs, or conflicts. In this case, you can force restart your iOS device to fix it.

    Turn on your iPhone / iPad and keep pressing the Power and Home button at the same time for about 10 seconds. If you are using an iPhone X, iPhone XS Max, or a newer model like iPhone 11, here you can press and hold the Power and Volume Down button. Keep pressing the buttons until the Apple logo appears on the screen.

    How to activate iPhone or iPad using iTunes

    In addition to directly activating the iPhone iPad on your iOS device, you can activate it using iTunes. So when you face the problem cannot activate iPhone iPad, you can turn to iTunes to get the job done.

    Step 1 Launch the latest iTunes on your computer and connect your iPhone to it with a lightning cable. When you see the iPhone or iPad icon appear in the interface, it means your iOS device is recognized successfully.

    Step 2 Click on the iOS device icon and then you will enter the Activate iPhone or Activate iPad window. Here you can enter your Apple ID and password and then click on Continue to start activating your iPhone or iPad.

    Top 5 Ways to Fix Can’t Activate iPhone iPad Problem

    You need to activate it when you get a new iPhone / iPad or update to a new iOS version such as iOS 13 / iOS12. This is the first thing to set up and start a new journey on your iOS device. However, many users have complained about the problem of unable to activate iPhone iPad, you face the same situation?

    When you suffer from one of the above situations, you can search the internet for a solution with keywords like my iPhone’s screen is frozen, my iPhone is frozen and won’t turn off, etc. As a result, you become more and more confused about how to fix this problem.

    In fact, there are many reasons that can cause the “Failed to activate iPhone” or “Failed to activate iPad” error when trying to set up a new iOS device. In some cases, you may receive a warning that the activation server is unavailable or the SIM card is not supported. In this post, we will share 5 easy ways to help you fix iPhone iPad cannot be activated problem.

    READ  Turn off Find iPhone in iCloud Settings

    reboot to fix Failed to Activate iPhone iPad

    Restarting Your device will always be the first attempt to solve various problems, including the iPhone or iPad failed to activate. If you are just getting a new iOS device or updating iOS to iOS 13 or iOS 12, you can try restarting your computer to fix the problem that cannot be activated.

    You can turn off your iPhone / iPad in the usual way and then restart it. Just keep pressing the Side Compare buttons and the Volume Down / Up buttons until a slider appears on the screen. Then drag the slider to the right to turn it off. Or you can go to the Settings app. Here you can click General Shutdown to pop up Presentation to shutdown and then drag the slider from left to right to do the same job.

    After restarting, you can start setting up and reactivating iPhone iPad to check if the issue is resolved.

    Professional way to fix the problem cannot activate iPhone iPad problem

    With the above methods, you have a great chance of successfully activating iPhone iPad. What if the problem still exists? It’s time to turn to a professional solution. Here we highly recommend a powerful iOS troubleshooter, iOS System Restore to help you fix unable to activate iPhone iPad problem.

    FoneLab allows you to transfer iPhone / iPad / iPod from DFU mode, recovery mode, Apple logo, headphone mode, etc. to normal without data loss.

    • Fix Disabled iOS System Issues.
    • Extract data from disconnected iOS devices without data loss.
    • It’s safe and easy to use.

    Step 1 Click the download button above and follow the instructions to install and run iOS System Recovery on your computer for free. It offers both Windows and Mac versions. Here you need to download the correct version based on your system. When you enter the main interface, select the iOS System Restore function.

    Connect your iPhone or iPad to it using a lightning USB cable. To help your computer recognize your iOS device, click here Trust this computer on the screen of your iOS device. Click on Run to go to the next step.

    Step 2 You can choose Standard Mode or Advanced Mode to fix iPhone failed to activate problems with iPad. Click on the confirm button and then check the specific information of your iOS device. Then click Repair to start fixing iPhone, iPad cannot be activated.

    It will take some time to fix iPhone failed to activate problems with iPad. After that, you can reactivate your iOS device normally. iOS System Recovery is specially designed to fix various iOS issues. You can rely on it to fix iPhone stuck on Apple logo, iPhone red / blue screen and more. Just download it for free to fix the problem.

    We talked about the failed to activate iPhone iPad issue in this post. We have shared 5 simple and effective ways to solve the problem. If you still have any questions, just leave your messages in the Комментарии и мнения владельцев.

    Reasons for the error

    Do not worry about the smartphone, as this glitch occurs on a global scale. it often affects smartphone owners around the world. The problem has a technical, not software origin, therefore it is not possible to eliminate it mainly by means of special software.

    IT news

    After the latest updates for iOS, during the restart process, it informs about the impossibility of activating Touch ID. As a result, access to Touch ID is blocked, which leads to serious problems. Consider ways to solve the problem.

    Touch ID activation error

    How to fix the error. standard calibration system

    The easiest method to troubleshoot Touch ID is to re-create your fingerprint. Recently, Apple developers have made many updates in this direction, including fixes for crashes with Touch ID.

    This method will help if your fingers have undergone some changes in recent weeks or years due to wear, dry skin or other reasons. To obtain a more detailed print, the following step-by-step algorithm must be carried out:

    • Open the Settings menu and enter Touch ID. Provide your own password when opening such a request.
    • Select problem fingerprint.
    • Remove it from the base.
    • Fill in a new print and scan again.
    • Scan your finger on the Touch ID sensor using different methods. from side to side, top to bottom and bottom to top. This procedure must be carried out until the print is painted over the entire surface.
    • When the smartphone asks for the capture settings, you need to scan the edges also before fully painting the surface of the scan.
    • Click “Continue” and wait for the process to complete.

    Actionable recommendations

    To remove the results of incorrect Touch ID settings, you need to take into account the following expert advice:

    • Download for Apple device update 12.2, then the crash with Touch ID is mainly solved.
    • Make sure the fingerprint reader is clean and dry. It is tedious to clean the button, the print with a napkin, and before that it is important to remove dirt, moisture and stains, since they “smear” and blur the print.
    • Make sure your finger is snug against the Home key and the surrounding ring.
    • Click on the button slowly, and do not move your finger during scanning.
    • Accessory elements must not touch or cover the Touch ID button (for this purpose, you need to remove the cover or cover).
    • Select a Touch ID setting and passcode. You should check unlocking the gadget and launching iTunes.
    • One or a couple of prints must be present in the device database.
    • Apply forced reboot: hold the Home and Wake key in parallel until the Apple name screen lights up.
    • Sometimes a crash in Touch ID resolves to resetting the device to its original settings. To implement this measure, you will need to go into the settings, find the key options and click on the reset category.

    There is another effective method for solving the problem. reconnecting the Touch ID loop, which must be performed by a specialist. To perform this measure, you must disassemble the smartphone, disconnect the Home cable and reconnect it.

    Fixing a crash with Touch ID defies standard explanations, for this reason, you need to install iOS updates to 12.2, as well as control the quality and density of the print. In complicated situations, it is worth coming to the service center to the masters.

    IPhone dfu mode how to enter dfu mode

    You must exit any running games before launching FACEIT AC

    Error codes 01-01, 20-01, 01-05 in the Sberbank Online application. how to solve the problem?

    Failed to activate Touch ID on this iPhone 5s and 6 what to do

    After performing a system update of iOS (usually updates to versions 10 / 10.1 / 10.2 / 10.3.2), the user’s iPhone may start displaying the message “Failed to activate Touch ID on this iPhone” upon reboot. Access to the user’s Touch ID is blocked, and various “dances with a tambourine” aimed at correcting the situation are usually ineffective. In this article I will tell you what this error is and how you can fix it.

    Causes of Touch ID Error on iPhone

    This problem is international in nature and is faced by many users around the world. Apple forums are full of complaints from Apple owners about a problem with activating Touch ID, which usually appears after installing system updates 10 / 10.1 / 10.2 / 10.3.2 on the iPhone.

    How to fix “Failed to activate Touch ID on this iPhone” problem

    To get rid of the unsuccessful activation of Touch ID, I recommend doing the following:

      Install update 10.3.3 for your iOS. For some users, the problem was solved in a similar way;

    Install update 10.3.3 for your iOS

  • Make sure you have the latest version of iOS installed;
  • Also make sure your fingers, as well as the Home button, are dry and clean. If necessary, use a clean, soft cloth to clean the surface of the Home button from dirt, moisture, etc.;
  • Your finger should be in full contact with the surface of the Home button, touching the metal ring surrounding the button. When scanning your finger with Touch ID, you must not press too quickly, or move your finger around the button;
  • If you use special tools to protect the screen, make sure that they do not cover the surface of the Home button, or the ring surrounding this button;
  • Go to “Settings”, select “Touch ID and Passcode” there, and make sure that the phone unlocker or “iTunes App Store” is turned on (value “on”), and that the phone already has fingerprints of one or more of your fingers;
  • Try adding another fingerprint to your phone;
  • Use a forced restart of the phone. Hold down the Home and Wake / Sleep buttons for 15-20 seconds until the Apple logo appears;
  • Try resetting your iPhone to factory defaults. To do this, go to “Settings”, then to “General”, then to “Reset”. “Reset all settings”;
  • If possible, roll back the system to the previous (before update 10) state (some users were helped by a rollback to update 9.3.5);
  • For some users, reconnecting the Touch ID loop helped solve this problem. To do this, you need to disassemble the iPhone, disconnect the “Home” button cable, and then reconnect it. It is recommended to perform this operation if you have sufficient qualifications, otherwise you risk putting the phone out of order;
  • If you are unable to add more than one of your fingerprints to the phone database, contact the Apple Retail Store or Apple Authorized Service Provider with this problem, also try to write to Apple support;
  • Visit the nearest service center to see if they can help fix the problem with activating Touch ID.
  • How to fix the problem. classic calibration scheme

    Today, the easiest way to solve the problem with Touch ID is to recreate the fingerprint. Apple has done a lot of work in this area over the past few years, including also focusing on fixing bugs with Touch ID.

    This can be helpful if your fingerprints have changed slightly over the past months or years due to wear and tear, dry skin, or other reasons. For calibration, it is worth doing the following percentages:

    • Launch the “Settings” application and go to the “Touch ID and Passcode” section.
    • Enter your password when prompted to do so.
    • Select the fingerprint with which there were login problems.
    • Click on “delete fingerprint”.
    • Click on “Add fingerprint” and re-scan.
    • Place your finger on the Touch ID sensor in different ways. from the sides, from top to bottom, and from right to left. This should be done until the fingerprint is completely colored.
    • After the phone asks you to set up the grip, you should scan the edges of your finger. This must be done until the print is completely colored.
    • Click on “Continue” and wait until the process is complete.

    Note: it is worth putting your finger on the way it will lie on the sensor with a comfortable grip of the device.

    Failed to activate Touch ID on this iPhone

    After some system updates for iOS, the iPhone may display a notification like “Failed to activate Touch ID” during reboot. As a result, access to the Touch ID system for the user is blocked, which can lead to more serious failures. How to solve the error?

    A Few Tips

    In order to eliminate the consequences of an unsuccessful activation of the Touch ID service, there are some tips to keep in mind:

    • Install update 10.3.3 for your Apple gadget. A number of users have solved the problem with Touch ID this way.
    • Make sure your fingerprint as well as the Home button are clean and dry. If necessary, wipe both the button and the fingerprint of a soft cloth thoroughly. It is important to remove any dirt, moisture and grease stains, as they will “smudge” and blur the print when using Touch ID.
    • You also need to make sure that the fingerprint fits as tightly as possible to the Home button and to the ring that surrounds this button.
    • Pressing the Home button is necessary not too quickly, and during authorization in this way you cannot move your finger.
    • It is also important to make sure that the protective and additional tools do not touch or cover the button with the Touch ID sensor (this is in the event that the user uses any additional tools to protect the display, such as a protective screen or case).
    • You can also go to Settings and select Touch ID and Passcode there. ” It is important here to make sure that the gadget unlocker and the iTunes App Store are running (that is, they are set to on).
    • Another point to be sure is that the database of your personal gadget contains prints of one or, even better, several fingers.
    • You can use a forced restart. To do this, hold down the Home button and the Wake / Sleep button at the same time for 20 seconds or until the Apple logo appears on the display.
    • In which cases, the problem with Touch ID can be solved by resetting all gadget settings to their factory values. In order to do this, you need to go to the settings, find the basic settings there and select the reset section.
    READ  How to pair watch with iPhone

    Do not forget about another way to solve the problem, only more radical and requiring the qualified help of an experienced specialist. It’s about reconnecting the Touch ID loop. In order to do this, you must first disassemble the phone, and then disconnect the Home button loop from the general device and connect this loop back. And, as mentioned above, it is better to make sure that this procedure is performed by qualified and experienced specialists.

    What causes the error

    Do not worry too much about your phone, since this problem is international in nature. users all over the world face it in one way or another. As noted by Apple employees and others, this problem is hardware, not software. For this reason, most often it will be impossible to solve it using applications or programs.

    Experts note that a software solution to the problem with Touch ID is more the exception than the rule, so you should not only update iOS to version 10.3.3, but also check the quality of the contact of the fingertip. In especially difficult cases, it is still recommended to contact a specialist.

    Touch ID Stopped Working. How I Solved This Problem!?

    Hello everyone! As has been repeatedly noted on the blog, all articles are those problems or questions that either I myself or my acquaintances have encountered. Actually for this, the site was created. to share personal experience and help others with the “apple” technique. And so, my already quite old, but still working iPhone 5S “threw” me another idea for the instruction. it suddenly stopped working Touch ID.

    And, as it seemed to me at the first moment, it happened finally and irrevocably. No, but what else can you expect? The device is far from new. Chips, scratches, scuffs, falls. all this was and is. Natural wear and tear of the device. there is no escape 🙂 Therefore, when the Touch ID fell off, I was not very surprised. Surprise came only later, in the process of solving this problem however, let’s talk about everything in order.

    • I upgraded to iOS 10.3.1
    • After some time, I began to notice that the sensor for unlocking does not always work. But as usual I did not attach any importance to this. maybe the hands are dirty or something else.
    • But after I could not enter the client bank by fingerprint, in my head “solitaire” was formed. Touch ID does not work.

    Looking ahead, I will note that everything was resolved safely. But what actions had to be taken for this?

    Unable To Activate Touch ID on this iPhone,unable to complete Touch ID setup.touch Id failed,error?

    It is worth noting that if your iPhone has a non-native Home button (for example, replaced after repair), then Touch ID will not function on it. Never. The fingerprint sensor is hard-wired to the motherboard. One board. one Home button. Also, some sellers immediately sell an iPhone with an inoperative scanner. I already wrote what kind of devices they are.

    But our problem is different. the iPhone stopped recognizing the fingerprint, although nothing happened to it (except for the iOS update).

    I thought it was a simple “glitch” of the system and did this:

    • To begin with, I forcibly performed a hard reboot. it’s very simple. And in some cases it helps to get rid of system crashes. But not at this time.
    • Opened “Settings. Touch ID and Passcode”, deleted the old fingerprint and tried to add a new one. There were no problems with the removal, but at the stage of adding a new one, the scanner simply did not read my finger and showed a white screen. Sometimes adding an inscription. “You pressed the button. Place your finger on the Home button without pressing it “.
    • Well, I think things are really bad. we need to do a firmware restore. Backed up and recovered

    And here, it would seem, everything should end. But no. the miracle didn’t happen and Touch ID still didn’t work. After that, it became clear that the problem was “iron”. And it consists in the loop of the Home button:

    • It may be damaged (moisture, careless assembly or disassembly of the device).
    • It may simply not be inserted (not fully installed).

    And it seems like this is not my case. I didn’t wet the iPhone, and since the last disassembly the scanner worked fine

    But all the same, the device had to be disassembled and this is what happened:

    • I took apart the iPhone.
    • Disconnected the loop of the Home button.
    • Looked at him and, as expected, saw nothing. he is in perfect condition.
    • Put it back.
    • Touch ID is working.

    Honestly, the result I got surprised me a little 🙂

    I don’t know why a simple reconnection of the loop helped, but the fact remains. after this operation, the button began to process my fingerprints normally.

    Although I have one idea why this could happen. lately my iPhone has dropped several times (and quite hard). I already thought that it would come to replacing the screen, but in the end well, everything worked out. And, perhaps, it was these falls that caused all the malfunctions that were described just above.

    Restart iPhone

    Problems with activating the iPhone can be solved after a banal reboot of the smartphone. Reboot your device and try activating it again.

    When trying to activate, it fails: “Your iPhone could not be activated because the activation server is temporarily unavailable

    Activating iPhone is a simple process and is made by Apple developers intuitively, however, problems can arise here too. One of the most common errors is associated with the message “Your iPhone could not be activated because the activation server is temporarily unavailable”. we will tell you how to get rid of it in this manual.

    Right now, a huge number of users from all over the world are trying to update to iOS 9.3. Even strong Apple servers cannot resist such a serious influx of people who want to install new firmware, so many people have errors when updating. In order to avoid any problems, it is strongly recommended to postpone the update to iOS 9.3 for at least a few hours. After the Apple update servers start working normally, you can install the latest version of iOS on your iPhone, iPad or iPod touch without incident.

    During iPhone activation, you may encounter various errors, the list of which is listed below:

    Unable to activate touch id on this iPhone error on iPhone

    • “Your iPhone could not be activated because the activation server is temporarily unavailable.”
    • IPhone is not recognized and cannot be activated for service
    • “The SIM card is not supported on this iPhone.”
    • “ITunes cannot check the device”

    If one of these messages is displayed on the screen of your iPhone, try our advice. one of them will definitely help you cope with the problem situation.

    Use a different Wi-Fi connection

    A Wi-Fi connection blocking the smartphone’s connection to Apple servers may be one of the reasons why you cannot activate your iPhone. Please try another wireless connection and try again.

    Insert SIM

    New iPhone owners are often in such a hurry to get to know their device that they completely forget about the need to install a SIM card. In this case, it is not necessary to reboot the smartphone. the activation process will continue immediately after installing the “SIM”.

    If the SIM card is inserted, then you need to make sure that it works. Try using a different SIM card and retry activation.

    Try activating your iPhone through iTunes

    Connect your iPhone to your computer, open the latest iTunes and try to activate your smartphone. This method is best used if you do not have the ability to connect to another Wi-Fi network.

    Restore iPhone via iTunes

    In most cases, the first four tips will solve the problem with activating the iPhone, however, if all else fails, it’s time to connect the “heavy artillery”. Restoring iPhone is done as follows: while holding and holding the Home button, connect your smartphone to the computer. The device will be recognized by iTunes in recovery mode, after which you will need to click the “Restore” button.

    Please rate 5 stars at the bottom of the article if you like this topic. Subscribe to us Telegram. In contact with. Instagram. Youtube.

    activate Touch ID from Settings on iPhone

    The most direct solution to the issue of when users cannot activate Touch ID.

    • Open your iPhone’s Settings app.
    • Find and open “Touch ID and Passcode”.
    • Enter your password.
    • Disable the iTunes app and restart your iPhone.
    • After rebooting, open the Settings app again.
    • Turn off iTunes and App Store.
    • Here you can add a new fingerprint. Delete the existing fingerprint before proceeding. Just click on the “Delete” button.
    • Add a new fingerprint by placing your finger in the designated area and following the instructions to make the correct settings.
    • Reboot your phone. The new fingerprint will be activated.

    What to do if you can’t activate Touch ID on iPhone?

    The fingerprint sensor found on almost every modern Android smartphone is called Touch ID on the iPhone. A proprietary scanner is used to lock and unlock your iOS device. Sometimes users faced problems related to Touch ID, for example, they were unable to activate it. In this article, you will find all the information you need to solve this problem. Methods work with any model of Apple devices.

    reboot device

    Restarting your iPhone is sometimes a great solution. Performing this action periodically is useful for other minor problems as well.

    Restarting iPhone 6 and Earlier Models

    To do this, you need to press and hold the Power and Home buttons at the same time. Wait for the Apple logo to appear on the screen. Release the buttons.

    How to restart iPhone 7 and 7 Plus

    Press and hold the power and volume buttons at the same time. Wait until you see the Apple branding on your screen. Release the buttons.

    How to reset iPhone 8, 8 Plus, X, XS, XS Max, XR

    Press the volume up button and quickly release.

    Immediately after that, press and hold the volume down button and the power button at the same time. Wait until you see the Apple branding on your screen. Release the buttons.